Ahollow tube having an inside diameter of (3cm) and a wall thickness of (0.5mm) is exposed to an enviroment at (h= 100 W/m?. ) and (T fluid is = 40C). What heat generation rate in the tube will produce amaximum tube temperatur of 250C for k=30w/m.k Assume the inner surface is insulated.What are the pati of heat?

Ahollow tube having an inside diameter of (3cm) and a wall thickness of (0.5mm) is exposed to an enviroment at (h= 100 W/m?. ) and (T fluid is = 40C). What heat generation rate in the tube will produce amaximum tube temperatur of 250C for k=30w/m.k Assume the inner surface is insulated.What are the pati of heat?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

no previous attempt pls. ssume adibatic tip
14- A south wall group D at (32 oN, Kw = 0.65). The room temperature is (24 oC). The maximum outside temperature is (42 oC). The daily range is (12 oC). Its heat transfer coefficient is (1.2 W/m2.oC) and dimensions are (5 x 3 m) with door of dimensions of (1.5 x 2 m). At (17 PM) in August, its Cooling load is Select one: a. 361.7 W b. None of these c. 261.7 W d. 303 W
A hollow tube having and a wall thick ness of (0:5mm) isexpased to an enviroment at (h= 100w/h-E) and (Too=40tWhet heat generation nate in the tube will produce an inside diia metes of (3cm) tabe temperatar the inner 250€ for kasowlinik a maximu m surface is insulatid. A heat. Assume O whet are the kate 2 Whet are
A stainless steel tube (AISI 304) with 36 mm internal diameter and 2mm wall thickness is used for transporting a fluidrefrigerated. The fluid is kept at 6oC and the ambient air is at 23oC, being the convective coefficients of the inner and outer sides equal to 100 W/(m2 oC) and 50 W/(m2 oC), respectively. A) If a 10 mm insulating layer is inserted into the surfaceexposed pipe (kiso=0.050 W/(m.K)), what will be the heat gainper unit of tube length and the new temperature of theexposed surface?
14- A south wall group D at (32 oN, Kw = 0.65). The room temperature is (24 oC). The maximum outside temperature is (42 oC). The daily range is (12 oC). Its heat transfer coefficient is (1.2 W/m2.0C) and dimensions are (5 x 3 m) with door of dimensions of (1.5 x 2 m). At (17 PM) in August, its Cooling load is Select one: Q2 a. 361.7 W b. None of these c. 261.7 W d. 303 W
not sure what happened
A room window measure (3 m?) constructed of glass with overall heat transfer coefficient of (4 W/m². °C). The inside design condition of room is ( 22 °C dbt and 50% RH) while the outside temp equals -7 °C. Determine; a) The inside glass surface temp b) Will moister condense on this window c) Select different glass type to prevent the vapoure condense over glass ( try to use two layers of glass with inside air gap (homemade) heat transfer coefficient for 6 mm at still layer (between two glass h=5.8 W/m2. °C))
A refrigeration system is being designed to maintain a small frozen storage room at -5°C. The required cooling rate is 50 kW. Waste heat from the refrigeration system will be rejected to the outdoor air at 35°C. The system will be designed such that the evaporation temperature will be either -10°C or -20°C, and the condensing temperature will be either 40°C or 50°C. UA cond For the 4 possible combinations of evaporator and condenser Tcond temperatures: Apply the "rule of thumb" to estimate the cooling COP Tn Есотp Estimate the required "size" of the evaporator heat exchange Practical Refrig surface, UA vap (W/°C) Estimate the required "size" of the condenser heat exchange surface, UAcond (W/°C) Тevap UAevap Show your work for Scenario A and complete the following table: Design Scenario Tevap (°C) СОР. UA. UA cond (W/°C) Tcond (°C) (W/°C) evap A -10 40 В -20 40 -10 50 -20 50
Plz solve correct and urgently i will upvote
Aplane wan of thickness 2h Was an internal heat generation that varies according -io cosax where oasthe heat genevated per unit volume at the centr of the wall ( X=0) cand (chis coustant. if both sides of the wall are maintained at acons trant te mp (Tw)-derive an expressian for the (Tル total heat loss from the wan per anit fuce face area sur
Ex-l A Steel ball cp=0.46 /Kgk K=35w/mk] 50mm in diameter and initially Sueddenly placed in a Controlled enviroment m which the templis mantained at. looi The convection heat transfer cocfficient islow/mk Calculate the time required fer the bullto attaina temp of I50 čf Poteet= 7800 kg/m) at a uniform tempof 450e is
A Figure illustrates the tube-flow system. The heat transfer under developed flow conditions when the flow remains laminar. The wall temperature is Tw, the center of the tube temperature is Te the radius of the tube is re, and the velocity at the center of the tube is uo. The velocity distribution equation is: 1 uo Prove that: 1 aT uor. T - T= a ax 4 ro Start the solution of the equation : P{żar drjuc,T 1 a ()- aT 1 әт ur дr ar « дх