Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and parallel to the column axis. If concrete has (E) of 15GPa and tensile strength of 2.8 MPa and the steel rods has (E) of (210) GPa and tensile strength of(400) GPa Determine the modulus of elasticity and tensile strength of composite if the steel rods occupy 10% of cross-sectional area of the column

Acolumn of rainforced concrete has steel reinforcing rods running through its entire length and parallel to the column axis. If concrete has (E) of 15GPa and tensile strength of 2.8 MPa and the steel rods has (E) of (210) GPa and tensile strength of(400) GPa Determine the modulus of elasticity and tensile strength of composite if the steel rods occupy 10% of cross-sectional area of the column

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. The bottom shell of a steel tanker is longitudinally framed. The spacings of transverse floor and longitudinal are 5 m and 0.8 m respectively. The bottom plating is 12 mm thick and the longitudinals are 150 x 10 mm flat bar. For higher- tensile steel, Young's modulus E = 210 kN/mm and yield stress oy = 340 N/mm?. Calculate the Euler buckling stress of the stiffened bottom panel and comment on the result. State any assumptions made. [342 N/mm]
A cantilever beam of circular cross-section is made of alloy steel is subjected to a fluctuating load that varies from -F to 2F. Determine the minimum ultimate strength of the beam material which can withstand the fluctuating loads. The variable forces on the beam induce corresponding fluctuating stresses between + 48 N/mm2 to -24 N/mm?. Assume the following values. Yield strength = 0.55 ultimate strength, endurance stress = 0.45 ultimate strength. Take a factor of safety = 2. Use Soderberg relation in your design i) Calculate mean and alternating stress ii) Calculate endurance strength **Note: Please upload your handwritten working/solution to the link provided. Mean Stress in N/mm^2 ... Variable Stress in N/mm^2 ... Endurance Strength in N/mm^2 .. Ultimate Strength in N/mm^2..
Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow)con = 2.4 ksi and (allow)st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 × 10³ ksi and for A-36 steel is 29 x 10³ ksi, (Figure 1) Figure 10 ft H 9 in. 9 in. Section a-a 1 of 1 Part A Determine the magnitude of the maximum allowable floor loading P Express your answer to three significant figures and include the appropriate units. Pmax = |153 Submit μA Provide Feedback ksi Previous Answers Request Answer * Incorrect; Try Again; 3 attempts remaining ?
This is a subject of strength of materialsShow complete solution and clear hand writing no shortcut pls shoe free body diagram and pressure diagram thank you
Introduction to Fem
A simply supported reinforced concrete beam carries a uniformly distributed load of 12 kN/m on a span of 4 m. The beam has a rectangular cross section 250 mm wide by 450 mm deep, with three 20 mm diameter steel bars placed 60 mm from the bottom of the beam, as shown below. The moduli of elasticity for the concrete and steel are 15 GPa and 200 GPa, respectively. Determine the average tensile stress in the steel and the maximum compressive stress in the concrete at the section of maximum bending moment. 450 mm 250 mm 60 mm
A round cast iron column 5m long and 299mm ...
Give me right solution according to the question... Urgenttttttttt please
For 10 to 12. The compound bar ABCD has a uniform cross-sectional area of 0.25 in². When the axial force P is applied, the length of the bar is reduced by 0.018 in. The moduli of elasticity are 29 x 106 psi for steel and 10 x 10 psi for aluminum. 18 in. 6 in. 18 in. P. P Steel B C Steel D -Aluminum 10. What is p? 11. What is the total elongation of the two steel sections? 12. What is the elongation of the aluminum section?
Diameter 14 mm, length 100 mm aluminum wire sample, axial When a load of 80 kg is applied in the tensile direction, the change in length and Calculate the change in diameter.(Ealuminum=70 Gpa)
Note: indicate Free body diagram
2.4-3 question