a. Some materials exhibit the property of superconductivity under certain conditions. State what is meant by superconductivity and explain the required conditions for the material to become superconducting. b. The diagram below shows the cross-section of a cable consisting of parallel filaments that can be made superconducting, embedded in a cylinder of copper. copper cylinder filament The cross-sectional area of the copper in the cable is 2.28 x 10- m?. The resistance of the copper in a 1.0 m length of the cable is 0.075 N. Calculate the resistivity of the copper, stating an appropriate unit. State and explain the what happen to the resistance of the cable when the embedded filaments of wire are made superconductive? i.

a. Some materials exhibit the property of superconductivity under certain conditions. State what is meant by superconductivity and explain the required conditions for the material to become superconducting. b. The diagram below shows the cross-section of a cable consisting of parallel filaments that can be made superconducting, embedded in a cylinder of copper. copper cylinder filament The cross-sectional area of the copper in the cable is 2.28 x 10- m?. The resistance of the copper in a 1.0 m length of the cable is 0.075 N. Calculate the resistivity of the copper, stating an appropriate unit. State and explain the what happen to the resistance of the cable when the embedded filaments of wire are made superconductive? i.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 14RQ

See similar textbooks

Similar questions

Question A suspension type insulator has three units with self-capacitance C and ground capacitance 0.1C. What will be the string efficiency?
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
Question 1 A ferromagnetic core with a relative permeability of 1500 is shown in Figure 2. The dimensions are as shown in the diagram, and the depth of the core is 7 cm. The air gaps on the left and right sides of the core are 0.070 and 0.020 cm, respectively. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 400 turns in the coil wrapped around the center leg of the core and if the current in the coil is 1.0 A, what is a) the flux in each of the left, center, and right legs of the core? b) the flux density in each air gap? 7 cm ст ст 30 cm 30 cm 7 cm 400 turns 0.05 cm 30 cm 0.07 cm 7 cm Core depth = 7 cm Figure 2
this is the ability of a material to conduct electricity a. impedane b. conductance c. reactance d. capacitance
We want to investigate how the field strength will be with air as dielectric and with steatite. A plate capacitor is placed in a 24 kV network between phase and ground. The relative permittivity of air is &=1 and for steatite &-6. The plate capacitor has area = 1m². The distance between the electrodes is 2 mm. Ep = 8.854-10-12 F/m A=1m² d=2mm a) Calculate the maximum field strength in the plate capacitor. (Answer: 9.8kV/mm) b) What is the capacitance of the capacitor if we use steatite? (Answer: C = 26.6nF)
Which of the following is not true for ferromagnetic materials? Please choose one: a. High?mthey have value. b.Above the Curie temperature, they lose their non-linear properties. C. a fixedµrthey have value. D.The energy loss is proportional to the area of the hysteresis loop.
What is dimensional formula of conductivity ,it's unit and answer in well manner step wise and also formula of conductivity?
Ferromagnetic materials have this characteristic. A. A relative permeability slightly less than one. B. A relative permeability slightly greater than one. C. A very high resistivity. D. A high relative permeability.
8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
Discuss the relationship between voltage break down and humidity, temperature and distance explain with curve
Okay for Determine the mathematical expression for the voltage vC and the current iC for the discharge phase. I got Vc = 8e-t/0.2s V and iC = -4e-t/0.2mA But I need help with the last question Plot the waveforms of vC and iC for a period of time extending from 0to 2 s from when the switch was thrown into position 1.
(b) A ferromagnetic is shown in figure Q3(b). Find the value of the current that will produce a flux of 0.005wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. The depth of the core is 5cm. The other dimensions of the core are as shown in the figure. 15 cm 500 turns 15 cm 45 cm 5 сm 15 cm 10 cm 35 cm Figure Q3(b)