a. One thousand cfm of outdoor air enters a building located in Regina, Saskatchewan, Canada. The indoor air design conditions are 72 F db and 30 % RH while the outdoor air design conditions are decided to be the 99.6% value. Assuming sea level pressure, compute the latent heat loss due to the outdoor air in Btu/hr. What will be the latent heat loss in case the building is located in Riyadh? b. Compute the lost head in feet of water for 2000 gpm of chilled water flowing through 1000 ft of 8" diameter schedule 40 commercial steel pipe.

a. One thousand cfm of outdoor air enters a building located in Regina, Saskatchewan, Canada. The indoor air design conditions are 72 F db and 30 % RH while the outdoor air design conditions are decided to be the 99.6% value. Assuming sea level pressure, compute the latent heat loss due to the outdoor air in Btu/hr. What will be the latent heat loss in case the building is located in Riyadh? b. Compute the lost head in feet of water for 2000 gpm of chilled water flowing through 1000 ft of 8" diameter schedule 40 commercial steel pipe.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. Discuss the influence of the bypass, coupling, internal, and stray capacitances on the frequency response.
Calculate the capacitance of a single phase 50 Hz overhead line 40 km long consisting of two parallel wires each 5 mm in diameter, 1.5 metres apart, taking the effect of ground into consideration. The height of the conductors above ground is 7 metres. Derive any formula used. [A.P.S. Univ. Electric Power Generation, Transmission and Distribution 1978) [Ans. 0.174 pF] A
In the Transmission Line Simulator, the Transmission Line is composed of which parameter/s? O A. The Shunt Conductance Only O B. The Series Impedance and Shunt Capacitance O C. The Shunt Capacitance Only O D. The Series Impedance Only
Q#5. Illustrate the variation of output power taken from the wind turbine? How the frequency in wind turbine is affected by excessive generation and load? Justify the relationship of frequency with power generation and load?
EXAMPLE A single-phase ac voltage controller has a 120-Vrms at 60 Hz, R = 10 Q, L = 50 mH, and a= 90°. (a) Determine an expression for the load current for the first half period. (b) Determine the rms of load current for the first half period. (c) Determine the rms current of SCR. (d) Determine the average current of SCR. (e) Determine the power delivered to the load. (f) Determine the power factor of the load.
Quest- A single phase 50 Hz, system supplies an inductive load of 5000 kw at power factor 0.8 lag through a line 25 km. Resistance of the line is 0.0195 2/km and inductance = 0.36 mH/km, receiving end voltage is 10 kV. A capacitor is connected across the load to get the voltage regulation of 10%. Ratio of transmission line loss with and without shunt capacitor is
Consider the circuit shown in Figure 2.23 in time domain. Convert the entire circuit into phasor domain.
Explore the concept of phasor measurement units (PMUs) and their role in real-time monitoring and control of power systems, emphasizing their contributions to the smart grid infrastructure.
Example 8.4 The one line diagram of a simple three-bus power system is shown in the figure. Each generator is j0.1 j0.2 represented by an emf behind the transient reactance. All impedances are expressed in per unit j0.1 j0.2 in a common 100 MVA base, and for simplicity, j0.8 resistances are neglected. The following assumption 2 are made: j0.4 j0.4 •shunt capacitances are neglected and the system is considered on no load. •all generators are running at their rated voltage 3 and rated frequency with their emf in phase Determine the fault current, the bus voltages and the line currents during the fault when a balanced three-phase fault with a fault impedance Z; = j0.16 %3D p.u. fault occurs on bus 3
2) A 200 ohm resistive load will be matched to a So ohm resstive source impedance. a) Calalate the L-C poss and high pass lumped matching netuwork component Values (tuo sets of L-C vales) b) Sketch the impedonce matching netwark that can be constructed by connec tion of short line segmants. C Assume 15 ohm and 150 ahm characteristic impedance lines are auailable tine lengths for realaing Determine the coriesponding one of the Salutions in part ()
The effect of the Shunt Capacitance is negligible only if the length of the Transmission Line does not exceed how many kilometers? A. 240 kms B. 120 km C. 300 km D. 80 kms
Question 1 A power system network, where the line data is given in table below. All the values are in p.u value. a) Determine the bus admittance matrix manually by considering the emfs source about 1.0Z 0° at Bus 1 with internal impedance of j0.8 N (See subtopic 6.2 in Hadi Saadat's book) R (p.u) 0.004 Х (р.u) 0.0533 В (р.u) From Bus To Bus 1 2 2 3 0.02 0.25 3 4 0.02 0.25 2 4 0.01 0.15 4 0.006 0.08