A. Find the values of K1 and K2 so that the closed-loop system resembles a second- order system with damping ratio equal to 0.5 and frequency of damped oscillations 9.5 rad/sec. B. With the above values of K1 and K2, find the percentage overshoot when input is step input. C. What is the settling time for 2 percent tolerance?

A. Find the values of K1 and K2 so that the closed-loop system resembles a second- order system with damping ratio equal to 0.5 and frequency of damped oscillations 9.5 rad/sec. B. With the above values of K1 and K2, find the percentage overshoot when input is step input. C. What is the settling time for 2 percent tolerance?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the type of feedback then b. vout c. the feedback fraction
Q-4. How many op-amps are required to implement this equation? V1+ R2 V. =- A) 3 B) 4 C) 2 D) 1 Q- 5. For the following feedback circuit. Identify the type of feedback and find the closed loop gain. E A ► VOUT
how to find the closed loop poles and zeros on a tf like this by hand. With unity feedback.
For the following op-amp circuit (i) (ii) (iii) (iv) R₁ R₂ What is the function of the circuit? Derive the mathematical expression for the closed loop voltage gain What is the high frequency closed loop gain if R₂ = 2.5 k2, R₂ = 50 kN and C = 20 nF? Calculate the cutoff frequency
One advantage of having feedback in op amp circuit is A.Can control gain B.less complicated C.less input signal D.low gain E.high output voltage F.low bandwidth
2. b) (i) Derive an expression for the differentiator using op-amp. (ii) Design a circuit to perform differentiation of an input signal that varies in frequency from 20HZ to about 2 KHz. (iii) If a sine wave of 0.5 V peak at 2 KHz is applied to the differentiator of part (ii), draw the output waveform.
Q2) Consider the following feedback system outlined in Figure Q2 Plant R(s) 10 C(s) S+1 Figure Q2 a) Derive the closed loop transfer function GRe(s). b) Calculate the value of Ky that will result in the closed loop system to have a maximum overshoot of 35% and a peak time of approximately 1 second. c) For the following systems assume zero initial conditions. Determine i) The peak overshoots. ii) Corresponding peak times iii) Decay rate characteristics. Produce a sketch of the unit step response using the above values calculated. vate ett
Ques 2: What is the Voltage series feedback? Explain the effect of feedback on gain and input, outputimpedance
(a) Identify the correct answers 1. Virtual ground of an OP-AMP (a) Is formed only with negative feedback (b) Is always an AC ground, may occasionally be a DC ground (for PMOS) (c) Is coined as a terminology where the input signal splits equally between the terminals (d) Leads to the concept of almost zero difference between the two inputs (both DC and AC) using feedback 2. In an OP-AMP based circuit (a) Phase margin of the closed loop transfer function is a measure of stable operation (b) 45° is a desirable phase margin as it balances the frequency domain stability and the time domain settling optimally (c) Absolute open loop gain numbers are not that important, as long as they are large (d) 45° is only achieved when the RHP zero is placed on one of the poles 3. In a differential amplifier biased with a given tail current I, to increase the overdrive voltage by 2X without changing input capacitive loading, we should (a) Increase W by 2X and reduce L by 2X (b) Reduce W by 2X and…
4- When a feedback voltage produces an increase in impedance, it is an example of......... a. Impedance compensation. c. Gain suppression. b. Shunt negative feedback. d. Series negative feedback
Consider the following feedback amplifier circuit. Assume lambda= 0, VDD RD2 R01 VinM₁ M₂ -Vout Select one: O a. none of these R₂ the open loop input resistance RinoL and the closed loop input resistances RincLare respectively: O b. RinoL = 1/gm and RincL= 1/gm(1+kA1) O C. RinoL = ∞o and Rincl= (1+ KA1) d. RinoLand RinCL = 00
a) Find the close loop transfer function of the following system through block diagram simplification b) Convert the block diagram in a) into a signal flow graph