Answered: A. Estimate the torque on a 10 mm…

A. Estimate the torque on a 10 mm dimeter steel shaft when yielding begins using (a) the Tresca and (b) the Von Mises theory. The yield strength of the steel is 140 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Give a complete solution, Don't use the direct formula. [1] A semicircular groove with a 5-mm radius…

Q: Q3 A solid shaft produced from 1045 steel must be 200 cm long and must survive continuous operation…

A: Given data: The length of the shaft, L=200 cm. The time of operations, t=1.5 years. The load…

Q: nce limit in reversed bending of 0.6 u s as follow; ka= 0.7, ksz 0.88, ksur: afety factor of 1.9.…

Q: Given: A ground steel rod with known diameter d is operating at temperature T. You are designing…

Q: 2.20. The uniaxial yield strength of annealed AISI 1015 steel is 386 MPa. Estimate the shear stress…

A: Given data: It is required to determine the shear stress according to the Tresca’s theory and…

Q: Explain the significance of understanding the effects of applying a torsional loading to a long…

A: EXPLANATION: The torsional strain on a circular cross-section causes the cross-section to twist…

Q: 9. A torsion tube is made from aluminium tube having an outside diameter of 60mm and a wall…

A: Given: The outside diameter of the tube, D = 60 mm The wall thickness of tube, t = 5 mm The young…

Q: In a torsion text, the specimen is a hollow shaft with 40 mm external and 20 mm internal diameter.…

A: Data given- D = 40 mm = 0.04 m d = 20 mm = 0.02 m T = 2 kNm Angular twist = 0.5° = 0.5×π/180…

Q: Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and…

Q: (7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the…

Q: (2) A diesel engine developing 1,850 hp at 105 rpm is used on a ship to drive the propeller. The…

A: Shaft and axle are machine members which revolve in the machine like pulley and gears etc. As the…

Q: In a torsion text, the specimen is a hollow shaft with 40 mm external and 20 mm internal diameter.…

Q: A solid circular shafts is made of the 650°C temper 300-M steel with properties shown in the table.…

Q: 5) A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length…

A: Given: Diameter of the brass rod=8mmLength of the rod=0.4mWall thickness t=3mmInternal diameter of…

Q: 2. A solid circular shaft has a diameter of 2 in. The shaft, in its current geometry, does not have…

A: The process to achieve a Three-fold increase in the polar moment of inertia of the solid circular…

Q: A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to…

Q: A mild steel shaft of 48 mm diameter is subjected to a bending moment of 1850 Nm and a torque T. If…

Q: A 1.5 m length of 30mm diameter solid steel bar fixed at one end is subjected to a maximum bending…

Q: Required information A ductile hot-rolled steel bar has a minimum yield strength in tension and…

Q: If you could produce AISI 1020 steel with a grain size of 50 nm, what would be the expected yield…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: Calculate the fatigue strength of a steel shaft to sustain 80,000 cycles. The tensile strength and…

A: The given information in the problem is listed in the following attached image:

Q: A flat-rolling operation of 250 mm wide alloy stee Calculate roll torque

A: GIVEN: **Width (Wt)=250mm **Diameter of rollers (D)=600mm **Height before rolling (ho)=30mm**Height…

Q: Question 5 Answer the following questions concisely (no more than half a page per question): a What…

A: To find-: (a) Define, the strength, stiffness and stability in the mechanics of solids context. (b)…

Q: (2) A diesel engine developing 1,850 hp at 105 rpm is used on a ship to drive the propeller. The…

A: (a) Calculate the torque applied on the shaft. P=TωT=Pω=P2πN60=1850 hp746 W1 hp2π105 rpm60=125514.13…

Q: A 1 m length of 50 mm diameter steel bar is subjected to a torque of 230 Nm. Calculate the maximum…

Q: Determine the magnitude of the principle stress

A: Given; internal diamter(d)=100 mmthickness=5 mmpressure=10 MPatorque(T)=2000 Nm Acc. to question ,…

Q: A compound steel [G = 80 GPa] shaft consists of a solid 92-mm-diameter segment (1) and a solid…

Q: If the modulus of ragidity of steel 12 80GPa, what is the diameter of the shaft required? What is…

A: Given data: Modulus of rigidity of steel shaft = 80 GPa N = 240 RPM…

Q: (12) A 50mm shaft is 3.0m long& receives 45kW from a pulley mounted @ 2.0m form the left end. A…

Q: A solid steel shaft is subjected to a variable torque whose maximum value is 710 N-m. For a fatigue…

Q: A flywheel is to be fitted on a punching machine with 73% mechanical efficiency. The machine makes…

A: Write the given data in the problem. n=20 strokes/mind=20 mm t=12 mmη=73% τ=330 MPa Here, n is the…

Q: The shear stress at a point in a shaft subjected to a torque is (a) directly proportional to the…

A: Write the basic mathematical torsion equation. TJ=τR=GθL Here, The torque on the object is "T" The…

Q: (2) A 1015 hot-rolled steel circular operating in an environment of 485 °F. If S-110ksi, S=50 ksi…

A: Given: The type of material = 1015 hot rolled steel at 485°C The ultimate strength of shaft, Sut =…

Q: Q.1 The ultimate tensile strength of the material is 1000 MPa and yield strength of 910 MPa. A rod…

Q: A aluminium rod of diameter 45 mm is subjected to a torque of 79 Nm. Assume one end is fixed of the…

A: Given:Diameter of rod,d=45mm=0.045mSo,Radius of rod,r=d2=0.0225 mTorque on rod=79NmLet the hear…

Q: A 9 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.8 kN and a…

Q: A 1045HR steel bar has a diameter of 40mm and it will be put under a fully reversible torsional load…

A: The material's endurance limit (Se) or fatigue limit is defined as the stress below which it can…

Q: A brass rod 8mm diameter and 400mm long fits centrally inside aluminum tube of the same length…

Q: 1) An aluminum alloy bar has a circular cross section of 20 mm diameter, length 120 mm and shear…

Q: A steel tube with outer and inner diameters are 86mm and 52mm respectively is twisted by torques at…

A: The section modulus of the hollow shaft can be determined as shown below.

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A. Estimate the torque on a 10 mm dimeter steel shaft when yielding begins using (a) the Tresca and (b) the Von Mises
theory. The yield strength of the steel is 140 MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Assume if the shear stress in steel exceeds about 4.00 x 108 N/m² the steel ruptures. .(a)..Determine the shearing force necessary to shear a steel bolt 1.05 cm in diameter. Enter a number. differs significantly from the correct answer. Rework your solution from the beginning and check each step carefully. N (b) Determine the shearing force necessary to punch a 2.00-cm-diameter hole in a steel plate 0.410 cm thick. N
Please help me solve this. I need answer asap. Tysm!! A flanged bolt coupling consists of eight d-mm diameter steel bolts on a bolt circle 275 mm in diameter, and four d-mm diameter steel bolts on a concentric bolt circle 193 mm in diameter. If the torque that can be applied is 9821 Nm without exceeding a shearing stress of 54.36 MPa in the bolts, what is the diameter of the bolts? Round off the final answer to two decimal places.
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?
Please answer asap I will give u ggod rating if u do not copy. thank u and please solve by yourself.
E 300 Nm- 600 N-m T₁ 900 N-m The solid aluminum shaft has a diameter of 46 mm and an allowable shear stress of Tallow = 65 MPa. (Figure 1) Part A Determine the largest torque T₁ that can be applied to the shaft if it is also subjected to the other torsional loadings. It is required that T₁ act in the direction shown. Express your answer to three significant figures and include appropriate units. Part B Determine the maximum shear stress within region CD. Express your answer to three significant figures and include appropriate units. Part C Determine the maximum shear stress within region DE. Express your answer to three significant figures and include appropriate units.
A rod specimen of ductile cast iron was tested in a torsion-testing machine. The rod diameter was 30 mm, and the rod length was 300 mm. When the applied torque reached 260.8 N·m, a shear strain of 1605 microradians was measured in the specimen. What was the angle of twist in the specimen?
ضحقهشمتلوظhelp
Please present drawings/FBD’s illustrating your solution.
Torsion in circular shafts From the figure as shown, the maximum shearing stress is 30 MPa and the angle of twist is 1.25°. Determine the maximum permissible torque? Use G = 80 GPa.
C G (5 esc ± § A9 cm diameter solid aluminum post is subjected to a horizontal force of V=8.5 kN and a concentrated torque of T=8.8 kNm, acting in the directions shown in the figure below. Assume that L= 0.5 m. The yield strength of the aluminum is oy = 250 MPa. Determine at point K: a) Normal stress due to bending caused by V. Enter your answer in MPa to 2 decimal places. Answer: 1 Check Question 2 Not complete Q @ 2 € W £ 3 # E S4 $ R % 5 T 6 Y & 7 U * 8 1 ( 9 O ) 0 P + [ ]