33333.From the given beam loaded as shown, Let P = 3 kN, L = 7 m, a = 3 m.E = 200GPa, I = 2000 x 10^6mm^4 3. Determine the following: Use Bracket MethodP|PkN/m2LBAD- L2La. Equation of the slopeb. Equation of the deflection curvec. The deflection at the midpoint.d. The slope at point B.

As per the company's policy, first 3 subparts will be answered.

Answered: a. Equation of the slope b. Equation of…

a. Equation of the slope b. Equation of the deflection curve c. The deflection at the midpoint. d. The slope at point B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Find the void ratio of soil if porosity is 0.102

A: given- The porosity of the soil, n=0.102

Q: A car weighing 3000 lb, with a wheel base of 9 ft carries 1700 ib of its load on the front wheels.…

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: 3. Before the trunk of a large tree is felled, cables AB and BC are attached as shown. Knowing that…

A: Given data, Tension in AB = 555 N Tension in BC = 660 N

Q: A line is recorded as 472.90m long using a 30m tape. During measurement, the temperature is 32°C and…

Q: Four wheel loads rolls as a unit across a 16-m span. The loads are 50 kN, 30 kN, 30 kN, and 20 kN…

A: L = 16m

Q: 3. Determine the following: Use Bracket Method P kN/m 2L P B A D 2L a. Equation of the slope b.…

A: As per company's guidelines we can only answer first three questions. Kindly post other questions…

Q: A cantilever beam, 90 mm wide by 220 mm high and 8 m long, carries a load that varies uniformly from…

Q: Three wheel loads rolls as a unit across a 12-m span, The loads are A 15 kN; B 25 kN. 2 m to the…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: For the given beam,

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 kN, 2 m to the…

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Q: 6. The results of a standard Proctor Test are tabulated as follows. Volume of Proctor Mold(ft³)…

A: a) Calculate the bulk density ,moist unit weight and dry density as given as , Bulk density =weight…

Q: A cantilever beam, 70 mm wide hy 290 mm high and 8 m long, carries a load that varies uniformly from…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: 4- Replace the distributed loading with an equivalent resultant force, and specify its location on…

Q: Determine the maximum shear in kips for the beams shown below using the method of consistent…

Q: Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional…

Q: A continuous beam ABC is loaded with uniformly varying load of 200 Ib/ft at left end support and 0…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Given data: U-2 m/s a=3.3 m/s2 t-3 Find final velocity

Q: A cantilever beam, 80 mm wide by 280 mm high and 8 m long, carries a load that varies uniformly from…

Q: What is the maximum bending moment in ft-lb at the fixed end of a 10 ft truss with a uniform weight…

Q: A plank of wood 200 mm thick is floating in seawater with specific gravity of 1.03. Find the minimum…

Q: For the structure below, determine the support reactions using METHOD OF CONSISTENT DEFORMATION.…

A: Given data:

Q: rtical planes at the point are Sx= 22 ksi, S, = 6 ksi, and Sy 13 ksi %3D Draw Mohr's circle for this…

A: σx=22ksiσy=-6ksiτxy=-13ksiRadius of the…

Q: The circular shaft shown is subjected to an axial force P at its free end and a compressive force of…

A: given, maximum allowable elongation =0.04 inches the shaft is hollow in between A & B having…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: 1. Replace the force system by a resultant force and couple moment at point O. 500 N 750 N 200 N 1 m…

A: A loaded cantilever beam is given and it has been asked to determine moment at o. Please refer step…

Q: cantilever beam, 100 mm wide by 260 mm high and 8 m long, carries a load that varies uniformly from…

Q: A truck with axle loads of 30 kN and 60 kN on a wheel base of 4 m rolls across a 14-m span. Compute…

Q: 2Pk/ft P k/ft A B -L- –L/2· -L/2→

Q: 3- Replace the distributed loading by an equivalent resultant force, and specify its location on the…

Q: on of 5; cm anywhere in the bridge during maintenance. Due to the controlled traffic scheme, 5 cars…

Q: The following noise records are obtained in a residential area. Is th in compliance with FHA noise…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Step 1 To Find stress at top fiber. Given data :- Gage length L = 230 mm Increase in length of AB =…

Q: A shell leaves a mortar with a muzzle velocity of 150 m/sec. upward at an angle of 60 degree with…

Q: Using Centroid by Composite Shapes, determine the x- and y-coordinates of the centroid of the shaded…

Q: Determine the reaction/s at each support, given the data and figure below. X 3 kN/m Y= 14 kN/m L= 3…

Q: Solve for the total hydrostatic force and its location with repect to oil surface S : 08 am 8m

Q: Determine the member end moments and reactions for the three-span continuous beam shown due to…

Q: Determine the moment at B for the beams shown using the three-moment equation. Express your answer…

Q: Design a lintel over an opening of 3.5 m. The lintel is made in a wall 400 mm thick. The lintel has…

Q: compacted asphalt concrete specimen has the following properties: a. Asphalt content = 5% by total…

Q: Find the moment of inertia (Ix, mm4) of the composite shape from the bottom base. Type answer in two…

A: To find out the moment of inertia of composite shape from bottom base. Where, X = 79 mm

Q: 4. Solve for the support reactions of the beam shown below using SDM. Assume beam is prismatic and…

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 %3D kN, 2 m to…

A: To Find :- moment at B in kN.m Given data :- Span = 12 m Loads at A = 15 kN B = 25 kN , 2 m right of…

Q: A В - L – - a·

Q: Consider a point in a structural member that issubjected to planestress. Normal and shear stress…

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa.…

Q: A car weighing 2000 lb, with a wheel base of 9 ft, carries 1300 lb of its load on the front wheels.…

A: weight = 2000 lb base = 9 ft we need to calculate the maximum moment in lb-ft when crossing a 14-ft…

Q: Determine the axial force (kN) in each member of the assembly shown below, Member Cross-Sectional…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

33333.

From the given beam loaded as shown, Let P = 3 kN, L = 7 m, a = 3 m.

E = 200GPa, I = 2000 x 10^6mm^4

3. Determine the following: Use Bracket Method
P
|P
kN/m
2L
B
A
D
- L
2L
a. Equation of the slope
b. Equation of the deflection curve
c. The deflection at the midpoint.
d. The slope at point B.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Support reactions

VIEW

Step 3 General equation for slope and deflection

VIEW

Step 4 Deflection at mid point E

VIEW

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

From the figure CPD-1. Determine the following: a. The maximum deflection in the beam. Use double integration method or conjugate beam methodb. Determine the slope at pt. A and B using method of superposition.
PROBLEM # 2: Determine the slope at point A and deflection at point C. "EI" is constant. Use moment area method. A C -x- L 2 2
2. Determine the following: Use Bracket Method |P | 2P A В C D L L а 2 a. Equation of the slope b. Equation of the deflection curve c. The deflection at the midpoint. d. The slope at point B.
USE CONJUGATE BEAM METHOD ONLY PLEASE! DON'T USE AMM AND DIM! Use Conjugate Beam Method. Determine the slope and displacement at point A using CBM. Assume C is pinned. 6KN/m 3m
Prob 01: Use method of virtual work and determine A. The displacement of point C of the beam made from steel. B. Slope at A of the beam made from steel. E = 29000 ksi, I 240 in* 12k 10 k B - 5 ft+S t- + Sft+5 ft-
3. determine the slope and deflection at point C. consider El as constant and start x from A. 10kN P d/2 2m B d 2m ст 20kN/m W d 2m D 우
Topic: Deflection of Beams (Geometric Methods) Area Moment and Conjugate Beam Situation #1 3 m El is Constant (Assume El = 1 kN-m²) 93 kN 7 14 192kN F4m B 7. Determine the slope at A 8. Determine the slope at B 9. Determine the location of the maximum deflection from A 10. Determine the maximum deflection All units must be kN or m. Be consistent with your units. Use ABSOLUTE values for your answers. Please show solution and Free Body Diagram
Use Conjugate Beam Method. Determine the slope at ends and midspan deflection. Use E = 29,000 ksi, I = 150 in“. %3D 6 kip/ft 5 kip-ft В -8 ft- -8 t-
Use slope deflection equation and calculate 'fixed-end moment' . Draw SFD, BMD. E, and I are constant.
▪ Determine the slope (in rad) and deflection (in mm) at 0.80m from the left if P = 225kN, E = 21000MPa, and I = 208x106mm4. Assume a = 0.50m and b = 0.7m. a.) Use double integration method. b.) Use moment area method c.) Use conjugate beam method 0 P P
Determine the slope at B and the disp lacement at C. EI constant. Use method of Virtual work. 6 k 6k B -10 ft 10 ft -10 ft-
(a) Draw qualitatively the deflection curve based on the bending moment diagram. (b) Determine the deflections at B and D, and the slope at C by the moment area method. (c) Locate the point of maximum deflection in AB and compute its magnitude. (E = 200GPa, I = 107mm4 ).