A Y-connected balanced three-phase generator with an impedance of 04 + j3 ohm per phase is connected to a Y-connected balanced load with an impedance of 24 +j19 ohm per phase. The line joining the Generator and the load has an impedance of 0.6 +0.7 ohm per phase. Assuming a positive sequence for the source voltages and that 120/30° V, Assume the abc sequence. Determine (a) the line voltages, (b) the line currents.

A Y-connected balanced three-phase generator with an impedance of 04 + j3 ohm per phase is connected to a Y-connected balanced load with an impedance of 24 +j19 ohm per phase. The line joining the Generator and the load has an impedance of 0.6 +0.7 ohm per phase. Assuming a positive sequence for the source voltages and that 120/30° V, Assume the abc sequence. Determine (a) the line voltages, (b) the line currents.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A balanced delta connected load of 13+j16 ohm per phase is connected at the end of a three-phase line. The line impedance is 2+j11 ohm- per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 Vrms. Taking phase "a" voltage Va as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal.
A balanced three-phase, negative sequence, Y-connected generator is connected to a three-phase balanced Y-connected load. The generator has an impedance of 1.5-j1.25 Q/phase. The impedance of the line connecting the generator to the load is 2.5+jl1.25 0/phase. The phase "B" load voltage is 1520° kV. The impedance of each phase of the Y-connected load is 60-j80 Q/phase. Calculate phase voltages \(V_{an}\) at the generator. \(V_{an}=\) Volts
Circuit theory. Y-connected balanced three-phase generator with an impedance of Zs =0.4+j0.3 ohm per phase is connected to a Y-connected balanced load with an impedance of ZL=14+j31 ohm per phase. The line joining the generator and the load has an impedance of Zl=0.6+j0.7 ohm per phase. Assuming a positive sequence for the source voltages and that amplitude of |Van|=188 and its phase angle 30 degree Find: (a) amplitude of the line voltage Vbc, (b) amplitude of the line current Ic, (c) the complex power at the balanced three-phase load. a. (a) Vb=325.63 V, (b) Ic=5.32 A, (c) S = 84006.67 + j 989.44 VA b. (a) Vb=265.87 V, (b) Ic=3.07 A, (c) S = 14001.11 + j 285.63 VA c. (a) Vb=325.63 V, (b) Ic=5.32 A, (c) S = 9508.07 + j 21053.59 VA d. (a) Vb=265.87 V, (b) Ic=5.32 A, (c) S = 3565.53 + j 7895.10 VA e. (a) Vb=325.63 V, (b) Ic=7.98 A, (c) S = 42003.33 + j 742.08 VA f. (a) Vb=325.63 V, (b) Ic=6.38 A, (c) S = 4754.04 + j 10526.80 VA g. (a) Vb=325.63 V, (b) Ic=5.32…
I need the answer as soon as possible
How did we get this result?
Three-Phase Power Calculations
A 3-phase transmission line supplies A-connected load z as shown in figure. The negative sequence current of phase R will be R Y B 25 20⁰ 25 / 180° Z ww Z Z
11 B/s A load of 120 MW at a power factor of 0.9 lagging can be delivered by a 3-phase transmission line. The voltage at the receiving end is to be maintained at 42 kV and the loss in the transmission is 8 % of the power delivered. (Consider the line to be a short transmission line) Find Single phase Power delivered Per phase voltage Current flowing through the transmission line 3 Phase Losses in the transmission line Per phase resistance of the transmission line II
Let the three-phase electrical system be illustrated in Figure . Knowing that its phase sequence is ABC and that Vcb=380∠135°V, determine the following: a) The value of the line currents demanded by each of the loads and supplied by the source. b) The power and power factor of each load and source. c) The power of the capacitor bank that must be installed to correct the power factor to 0.95 lagging. d) The currents supplied by the source after installing the capacitor bank. e) The percentage reduction of the total apparent power supplied by the source after installing the capacitor bank.
A Y-A system has source voltages of 415Z-105° V on its a-phase and 415Z135° V on its c-phase. Determine the type of sequence of this system. If this Y-A system has source, line and load impedances of 6/45°2, 15 - j25 Q and 102230° Q respectively, obtain (a) The line currents (b) The load currents (c) The load voltages (d) The complex powers supplied by the sources
Two single-phase loads are connected in parallel, where load 1 is 4.7 kVA at 0.87 lagging power factor, and load 2 is5.2 kWat0.79lagging power factor. The load combination is connected to a voltage source of220VAC,50 Hz. a) Find the total complex power