A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 14 mm from the top of the beam on a section 3.4 m from A if P = 4619 N, W = 1991 N/m, a = 0.82 m, b = 1.77 m, c = 1.13 m, L = 68 mm and h = 197 mm. Round off the final answer to two decimal places.

A wood beam carries the loading shown in the figure. calculate the magnitude of the bending stress (in Pa) at a point 14 mm from the top of the beam on a section 3.4 m from A if P = 4619 N, W = 1991 N/m, a = 0.82 m, b = 1.77 m, c = 1.13 m, L = 68 mm and h = 197 mm. Round off the final answer to two decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure shown, the rigid beam with negligible mass was horizontal before the load P was applied. Determine the value of load P if the vertical movement at P is 3mm. Draw the FBD and deformation diagram.
At least four decimal places for the final answer.
The rectangular wood beam is loaded as shown in the figure. 12 kN. 8 KN/m 150 m 250 mm 10m 2 m What is the bending stress in the beam 2 meters from point A? 7.68 MPa O 5.76 MPa O 10.24 MPa 4.48 MPa What is the bending stress 50 mm from the top of the beam 0.5 meters from point A? * 3.456 MPa 5.760 MPa 10.245 MPa 6.144 MPa What is the shear stress in the beam at point C? O0.48 MPa 0.80 MPa 0.64 MPa O0.32 MPa
Assignment Problem 10.1. A steel bar of diameter d = 52 mm is twisted by torques at the ends. The allowable shear stress is 65 MPa. What is the maximum torque that can be applied?
I need the answer as soon as possible
SHOW YOUR SOLUTION.
The 100X200 mm cross section of the simple support beam given in the figure was obtained by gluing four pieces of wood of 50X100 mm to each other as shown in the figure. The shear safety stress for the adhesive is 0.35 MPa and the bending safety stress for wood is 11 MPa. Calculate the maximum force P that can be applied to a beam with a span of 3 m. The load is applied at a distance of 1 m from the left support. Include the weight of the beam itself in the process and take 5.5 kN / m3 for the weight of the wood. Draw the cross section diagrams (shear force and bending moment). Show how you draw using the separation technique.
3.5
The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span of 4.0 m. The bearn is built of a wood member having cross sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 150 mm x 50 mm. Determine the maximum stresses, in the steel and wood, respectively. If the moduli of elasticity are E {s} = 209GPA and E {w} = 11GPA (Disregard the weight of the beam) Steel 50 mm 50 kN/m Wood B Steel 50 mm 4.0 m- 150 mm 250 mm
USE ALL DECIMAL PLACES IN SOLUTIONS AND ROUND OFF YOUR ANSWERS TO NEAREST WHOLE NUMBER. INPUT NUMERICAL VALUE ONLY.
A simply supported wood beam is reinforced with a steel plate of width b as shown in the figure. The beam carries a uniformly distributed load including the weight of the beam) of intensity 279 lb/ft over its 22.3- ft span. Using b = 4 in. and Est/Ewd = 20, determine the maximum bending stress (in psi) in the steel. Round off the final answer to two decimal places. ... 6 in. 10 in. 1/2 in. -b-
A 3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 kN. Poisson’s Ratio = 0.25 and E = 200 000 MPa. Compute the lateral strain. Express your answers in 6 decimal places.