A wind turbine gives maximum output put of 1MW at a wind speed of 15m/s. Refer to the above wind turbine choose the correct statement a. The wind rotor swept area is 638 square meters. b. The wind rotor swept area is 835 square meters. c. The wind rotor swept area is 700 square meters d. The wind rotor swept area is 400square meters.

A wind turbine gives maximum output put of 1MW at a wind speed of 15m/s. Refer to the above wind turbine choose the correct statement a. The wind rotor swept area is 638 square meters. b. The wind rotor swept area is 835 square meters. c. The wind rotor swept area is 700 square meters d. The wind rotor swept area is 400square meters.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What justifies the need for plenumrated cabling above the ceiling tile?
Why is it necessary to carry out fault calculations? Compare between the p.u. system method and the referred Ohmic impedance method for fault calculations.
#14,#17
which side is short cct.in short cct. test ? why?
QUESTION 2: What is the approximate voltage amplitude and frequency of the waveform below
x Chapter-5B.pdf X Tale vebapps/assessment/take/take.jsp?course_assessment id%=_12957_1&course_id=_18638_18content_id= 214533_1&c PA- Remaining Time: 40 minutos, 39 seconds. Question Completion Status: Qbesion7 The fuel inputs per hr of plant-1 and plant-2 are given as F1 = 0.4P2 + 80P1 +240 OMR/hr F2 = 0.5P+ 60 P2 +300 OMR/hr Determine the economic operating schedule corresponding cost generation if the total load is 360MW.Neglect the line losses and generator limits. P1 = 188.89 P2 = 171.11 Total Cost = 54,829.12 OMR I hr P1 = 189.89 P2 = 170.11 Total Cost = 52,629.12 OMR I hr P1 = 185.89 P2 = 174.11 Total Cost = 58,429.12 OMR / hr تنشيط None
Complete the wiring below, such that the two sensors are connected in series and capable of controlling the given load. SENSORS in SERIES ... Brown Brown 0-30 Vpc SUPPLY Black Black PNP PNP Blue Blue
1. The system e'e-5 is: a. Linear, time invariant, casual. b. Non-linear, time invariant, non-casual. c. Non-linear, time varying, casual. d. Not all the above.
What precautions are practiced by electric companies in terms of loading capacity? When is a distribution box needed in terms of electrical supply?
16. A conductor installed from a bonding/grounding bushing that's used to provide a conducting connectionbetween a raceway and the enclosure that the raceway is connected to is an example of a/anA. grounding electrode conductor.B. bonding jumper.C. equipment grounding conductor.D. impedance device.
15.a. Which of the following is a common raceway installed for feeders supplying separate buildings orstructures?A. Nonmetallic underground conduitB. Flexible metallic tubingC. Rigid metal conduitD. Electrical metallic tubing 15.b. You're installing a feeder in a hospital that will terminate in five branch circuits in patient care areas. Tomake the feeder legal for this purpose in this area, you mustA. run a bonded and an isolated EGC.B. bond the neutral to a grounding electrode at both ends of the feeder.C. run two wire conductor EGCs.D. use enhanced bonding practices on the feeder's raceway
10. Identify the temperature range of Nickel wired RTD a. -100°_C to 300° C_ b. -80°_C to 200° C_ c. -80°_C to 600° C_ d. -80°_C to 300° C_