A well-insulated heat exchanger is to heat water (cp = 4.18 kJ/kg-°C) from 25°C to 60°C at a rate of 0.5kg/s. The heating is to be accomplished by geothermal water (cp 4.31 kJ/kg-°C) available at 140°C at a mass flow rate of 0.5 kg/s. What is the temperature of exit Brine. Water 25°C Brine 140°C 60°C

A well-insulated heat exchanger is to heat water (cp = 4.18 kJ/kg-°C) from 25°C to 60°C at a rate of 0.5kg/s. The heating is to be accomplished by geothermal water (cp 4.31 kJ/kg-°C) available at 140°C at a mass flow rate of 0.5 kg/s. What is the temperature of exit Brine. Water 25°C Brine 140°C 60°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

P7.5 P7.5 A single-pass evaporator of a water chiller has 100 horizontal copper tubes of inner diameter 15mm and wall thickness 1.5mm through which water flows with a total mass flow rate of 1.8 kgs. Refrigerant 134a undergoes pool boiling at 2°C on the outer surface of the tubes. The water is cooled from 14°C to 6°C. The water-side and refrigerant-side heat transfer coefficients are 1100 Wm 2K and 980 Wm ²K¹ respectively. Calculate (i) the overall heat transfer coefficient based on the inner tube area, (ii) the LMTD (iii) the effectiveness of the evaporator, and (iv) the length of a tube. [Answers: (i) 567 Wm ²K¹, (ii) 7.28°C, (iii) 0.67, (iv) 3.13m]
Consider the steady-state counterflow heat exchanger shown below. There are separate streams of air and water, and each stream experiences no noticeable change in pressure. Stray heat transfer with the surroundings and changes in kinetic and potential energy can be ignored. For the air, the ideal gas model can be applied and Rair = 0.287- For the operating conditions provided on kg-K the figure, determine: a. The temperature of the air at the outlet of the heat exchanger, T4, in [K] b. The rate of heat transfer between the air and the water, in [kW; , c. The rate of entropy production for the heat exchanger, in [kW/K] kg msteam = 12 P1 = 3 bar X1 = 1 P2 = P1 T2 = 200 P3 = 1 bar T3 = 1100 K P4 = P3 T, =? mair kg = 3.29
i need the answer quickly
In a heat exchanger, the heat transfer depends on the choice of the control volume
i need the answer quickly
A completely insulated mixing vessel is designed to deliver water at 60 ⁰Cand atmospheric pressure at a rate of 4 kg/s by mixing two streams of incomingwater in an environment at 25 ⁰C. Saturated steam at atmospheric pressure isinserted on the hot side. Two options are being considered for the cold side: (a)chilled water from the plant at 3 ⁰C or (b) water from the tap at 20 ⁰C (both atatmospheric pressure). 1. Determine the thermal efficiency of each process
A heat exchanger is to heat water (cp = 4.18 kJ/kg·oC) from 25oC to 60oC at a rate of 0.2 kg/s. The heating is to be accomplished by geothermal water (cp = 4.31 kJ/kg·oC) available at 159oC at a mass flow rate of 0.3 kg/s. Find the exit temperature of geothermal water.
Q.2. Air enters a steady-flow heat exchanger with a mass flow rate of 2 kg/s as shown in Figure. Determine (a) the rate of heat transfer to the air in the heat exchanger, (b) the power output from the turbine assuming no heat loss, and (c) the velocity at exit from the nozzle. (Cp atr = 1.005 kJ/kg. K) T=600 C T- 12 C V=3 m/s Air Нeat v-3 m/s Exchanger Turbine T= 200 C V - 25 m/s T= 160 C Nozzle
Q12 A refrigerator is used to remove a heat from a food at a rate of 532.6 kW and required a compressor power of 219 kW, what is the heat added to the surrounding (kW)? (D) 563.7 (A) 243.2 (B) 313.6 (C) 751.6 (E) None of them far infore?