A well-insulated 3-m 3 4-m 3 6-m room initially at 7°C is heated by the radiator of a steam- heating system. The radiator has a volume of 15 L and is filled with superheated vapor at 200 kPa and 200°C. At this moment both the inlet and the exit valves to the radiator are closed. A 120-W fan is used to distribute the air in the room. The pressure of the steam is observed to drop to 100 kPa after 45 min as a result of heat transfer to the room. Assuming constant specific heats for air at room temperature, determine the average temperature of air in 45 min. Assume the air pressure in the room remains constant at 100 kPa. Fan 7°C 3 mx 4 mx 6 m Steam radiator

A well-insulated 3-m 3 4-m 3 6-m room initially at 7°C is heated by the radiator of a steam- heating system. The radiator has a volume of 15 L and is filled with superheated vapor at 200 kPa and 200°C. At this moment both the inlet and the exit valves to the radiator are closed. A 120-W fan is used to distribute the air in the room. The pressure of the steam is observed to drop to 100 kPa after 45 min as a result of heat transfer to the room. Assuming constant specific heats for air at room temperature, determine the average temperature of air in 45 min. Assume the air pressure in the room remains constant at 100 kPa. Fan 7°C 3 mx 4 mx 6 m Steam radiator

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer part c and e onwards with working out and answer and please label the parts as you have answered a,b,d
In step 4, it should be the A and not the y right? So it should be FBD divided by 4.04 which is the cross-sectional area and not 6.9 which is the distance?
I need every step explained please
hii, what's the right formula for n? h2 will be subtracted in the numerator too as well as in the denominator, or not?
I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal places for magnitude. DO NOT FORGET YOUR UNITS. Enclose all final answers in a box. No need to copy the question or problem. File submissions should be a single PDF. II. PROBLEM SOLVING 1) Given the figures and data below, solve what is being asked for. Y-axis 200mm -200mm 50mm 50mm 100mm 200mm 100mm Y-axis Yo 200mm 100mm 3°1 100mm 547 - ATT HA LO - CHIR →→X-axis -Xo →X-axis
the suffix meaning
What about the stretch for OA?
How did you get 4/5 and 3/5?
HOME WORK Calculate the amounts of solid phases of ferrite and cementite present in pearlite. y+ FegC a + Fe;C 6.70 0.022 0.76 Composition (wt % C) Temperature
Question 3 10 points V Sav The basic principle to select a material for a product is to use a material with properties that meet or exceed the product performance requirements, and keep the cost of the product as low as possible to use a material with properties that meet the product performance requirements, and keep the cost of the product as low as possible to use a material with properties that exceed the product performance requirements as much as possible, and keep the cost of the product as low as possible to use a material with properties that meet or exceed the product performance requirements, and keep the cost of the material as low as possible
Q/ Correct the under line words 14. Al-4%. Mg alloys are produced by extrusion because has high strength 15. Mg -Zn - Zr alloy is not proper to produce by extrusion because of susceptible to micro porosity and can be used for casting process 16. Brass-alloys are expensive because of difficulties experienced of its casting 17. The density, T.S. and hardness of Fe alloys can be decreased by working
Diagram: Given the hook-up drawing, list all the equipment, tools and materials that are needed in installation. INST. PIPING 1- *1 INST. PIPING