Answered: A water sample contains 6.35 mg/L of…

A water sample contains 6.35 mg/L of calcium (Ca), 7.3 mg/L of magnesium (Mg) and sodium (Na) of 21 mg/L. What is the concentration of magnesium in (meq/L) Select one: O a. 5.98 O b. None O c. 0.598

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.32P

See similar textbooks

Related questions

Q: In a test to determine the discharge coefficient of a 50mm by 12.5mm venturi meter. The total weight…

A: Given, Inelt Diameter= 50mm Throat Diameter = 12.5mm Time = 7min Difference in mercury level (X)=…

Q: The velocity of oil flowing thru a 30 mm diameter pipe is equal to 2 m/s. Oil has a kinematic…

A: Given - Dia- 0.030 meter - kinematic viscosity - 5/10⁵ -length - 120 meter -Velocity - 2 meter…

Q: Determine the ultimate BOD of a waste water sample which was subjected to the BOD determination as…

A: This question is related waster water from Environment Engineering or waste water Engineering. In…

Q: A tank contains 1,500 L of water and 20 kg of dissolved salt. Fresh water is entering the tank at 15…

Q: 0 Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the…

A: Question No 1: Given data: weight of water = 3.5kn = 356.9kg Discharge will takes place in 5min As…

Q: Use the constant head permeability to find (K) in diameter cylinder 65 mm ,the length= 45 mm , AH=12…

A: Given-discharge=22cm3/dayConstant head causing flow=12mm=1.2cmlength=45mm=4.5cmDiamter =6.5cm

Q: A 63 cm diameter pipe is fitted to a venturi meter with a throat diameter of 24 cm as shown. During…

A: venturi meter is the flow measurement device is used for measurement of discharge the coefficient of…

Q: Following data are given for water sample taken from irrigation water: [Na+] = 250 mg/ml [Ca2+] =…

Q: 2. An open tank contains different liquids with specific gravities and depth. From the bottom of the…

A: To find specific gravity of olive oil

Q: Two rivers with different sodium (Na") levels converge and form a single river downstream of the…

A: River 1 : Na = 58.0 mg/L, Load = 7800 lb/day River 2: Na = 150.0 mg/L, Load = 5300 lb/day To…

Q: A 400-gallon capacity tank initially contains salt solutions consisting 150 gallon of water and 25…

Q: EA two-stage distiller system is used to remove TDS from sea water as shown in the figure. The…

A: Given:- two stage distiller To find:- concentration

Q: , g 19.44 18.78 18.75 22.10 Weight of container, g 12.74 13.24 13.20 13.27 Weight of…

Q: A container is filled with 0.675 liter of fluids at pressure of 2000 kPa. When the pressure…

Q: If 19.3mL of the standardized Na2S203 solution was used in determining the DO, what is the DO…

A: Given data- Volume of the sampleV=19.3 mLSolution taken is Na2S2O3 Sodium thiosulphate To Find- The…

Q: 5. A water sample has been analyzed. Upon titration with EDTA, the following results were gathered.…

A: Given, Volume of water sample = 10 ml Volume of CaCO3 = 5 ml

Q: Five-days BOD of a 10% diluted sample having Do = 6.7 mg/l, D = 2 mg/l and consumption of oxygen in…

A: Given data in question Dilution Dissolved Oxygen To find out 5 day BOD

Q: 21 Calculate the Liquid Limit, plastic limit and plasticity index. Results of liquid limit test 1…

Q: 4. Tank A initially holds 100 gallons of brine that contains 100 pounds of salt, and tank B holds 10…

A: Given, Initial salt content in tank A = 100 lb Volume of tank A = 100 gallon Volume of tank B = 10…

Q: If the 3-day, 15°C BOD is 200 mg/L, what will be its 7 day BOD at 25°C? Assume k20 (base 10) =…

A: We have to determine the value of 7 day BOD at 25°C as per the given data in the question like…

Q: Water is flowing through a 2 inch diameter pipe at a velocity of 4.3 ft/s. If the length of the pipe…

A: Given: Diameter, D = 2 in Velocity, v = 4.3 ft/s Length, L = 100 ft Kinematic viscosity = 1.21 x…

Q: Determine the dynamic viscosity (Pa-sec) and kinematic viscosity (m2/s) of water with a specific…

Q: 1. If concentration of Na+, Cat+ and Mg++ in a water sample are 345, 60 and 18 mg/I respectively,…

Q: Does the function, =Ur cose+cose represent possible irrotational flow? r

Q: GLYCERIN (SP.GR. VISCOSITY OF 1.49 Pa – s ) FLOWS THROUGH A RECTANGULAR CONDUIT 300 MM BY 450 MM AT…

A: Given data, Specific gravity = 1.26 so density p= 1260 kg/m^3 Discharge Q = 160 lit/s = 0.16 m^3/s…

Q: BOD Suspended solids chemical oxygen demand 270.7778 mg/l 312.3143 mg/l 585.8571 mg/l

A: Given Data:

Q: 8. A tank initially contains 40 gallons of pure water. A solution with 1 gram of salt per gallon of…

Q: 4. A closed, hollow, empty drum has a diameter of 24.0 in, a length of 48.0 in, and a weight of 70.0…

Q: GLYCERIN (SP.GR. = 1.26 AND VISCOSITY OF 1.49 Pa – s ) FLOWS THROUGH A RECTANGULAR CONDUIT 300 MM BY…

A: To answer Part B To find :- Head Loss per kilometer length of pipe

Q: If 19.3mL of the standardized Na2S2O3 solution was used in determining the DO, what is the DO…

A: 0.01 N Na2S2 O3 is used in titration to decolorized the blue solution and the volume of 0.01N Na2S2…

Q: A 20 mm diameter pipe has a length of 80 m. Water with a viscosity of 0.04 Pa-sec is flowing thru…

Q: If the concentration of Na, Ca and Mg in a water sample are 345, 60 and 18 mg/l, respectively, then…

A: This question is related to The Irrigation Engineering. In this question we calculate the SAR of…

Q: Consider a stormwater retention pond that has no outflow. The pond is initially filled with pristine…

Q: Q6 : - compute the values of K and L. using Thomas graphic method for a set of given data that give…

Q: Ground surface Groundwater table (free surface) irection I seepage Impervious layer permeable soil…

Q: A cank initially contains 10 kg of salt in 50 liters of water. Pure water enters at a rate of 2…

A: Solution: The differential equation of the mixing tank: dqdt=riCi-roqtvt given, q(0) = 10 kg ri = 2…

Q: Which of the following statements is INCORRECT about the mass transfer method of estimating.…

Q: 2. An oil having a specific gravity of 0.80 has a kinematic viscosity of 2x10°m²/s flows in a 100mm…

Q: 0 Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the…

Q: Q2/ Calculate the gas flow rate in sef/day for a natural gas is following in porous media at…

A: Given :

Q: Water Gs=1 1. In a test to determine the discharge coefficient of a 70 by 35 mm Venturi meter, the…

A: ''Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: II. Typically, the length (or height) of a portable cylindrical liquid container is longer than its…

A: Cylinder is a prismatic circular geometrical shape in three dimensional axis. It is usually…

Q: 7. Calculate the amount of lime (84%) and soda (92%) required for treatment of 20,000 litres of…

A: Temporary hardness is cause by the bicarbonates of calcium and magnesium where as permanent hardness…

Q: Given the following dissoived oxygen data for an aeration test with Cg = 9 mg/L, the KLa value…

A: Volumetric oxygen mass transfer coefficient=KLaKLa=KL×AVwhere A=inerfacial area of mass transfer…

Q: Q3: the 2000 gallon tank initially contains 600 gallons of water with 5 lbs of salt dissolved in it.…

Q: Two milliliters of 0.025molars potassium iodate solution was used to standardized the sodium…

A: Given data- 2 mL of 0.025 molars potassium iodate solutionsodium thiosulphate is standardized19.4 mL…

Q: Q. Determine the kinematic viscosity at the average temperature and determine the Reynolds number…

A: The kinematic viscosity and density of the fluid at the average temperature can be calculated by…

Q: Determine the dynamic viscosity (Pa-sec) and kinematic viscosity (m2/s) of water with a specific…

A: This question is related to the Fluid Mechanics.

Q: The absolute viscosity of the peanut oil is 41x10-3 Pa-s and the specific gravity is 0.95. If the…

A: The given data is shown below: Absolute viscosity=41×10-3 Pa-sSpecific gravity=0.95Discharge=8.6…

Q: 4. The results of the liquid limit tests are given below 11 No of blows Water Content (%) | 53.9…

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Quèstion 49 Avertical cylinder having a circular base of radius 'r and a height of 12 m is filled with water at the rate of 1 m-/min. If the depth of water in the cylinder at the vertical position is 3 m, what would be the resulting depth when the cylinder is in the horizontal position? O A.0.40r O B.0.60r OC.0.30r O D.0.50r « > A Moving to another question will save this response. acer F12 PrtSc Pause Del Home Pg Up F7 F8 F9 F10 F11 F3 F4 F5 F6 Scr Lk SysRq Break Ins * % Backspace 4 5 € 6 7 8 9. W E Y U P F G K
ONAN MENDER AYDIN ADNAN MENDERES ÜNİVERSİTESİ IVE ITESI ONLINE SINAV PORTALI 181803026 026 181803026 number for this flow is 181803028 Air flows in a pipe which has 5 cm diameter at a velocity of 4 m/s. dynamic viscosity=1.802x10 and density.1.225 kg/m The Reys 26 181803026 O A) 13596 181803026 181803 O B) 11098 O C) 12605 181803026 O D) 21770 181803026 O E) 16745 Kalan Süre 44 181803026 18180026 181803026 O Bu soruyu cevaplamadan geçmek için bu seçeneği işaretleyin 1818 161803028 Sorunun Cevabı Kaydet ve Sonraki Soruya Geç Antaly 181803026 03028 181802028 1818 181803026 181803026 3818 181803026 181803026 181803026 181803026 181803026 181803026 101803026 18T80300 18180306 18 1818030
Castor oil (SG = 0.96) uiny Problem 9: %3D A tank whose bottom is 18 inches x 18 inches is filled with 2 in. three liquid as shown: 12 inches of carbon (SG=1.59), 4 inches of water and 2 inches of (SG=0.96). Compute the total hydrostatic psi) acting at the bottom of the tank. tetrachloride water 4 in. castor oil Carbon tetrachloride 12 in. pressure (in (SG = 1.59)
Calculate the BOD concentration based on the data below. DOinitial (mg/L) 7 DO final (mg/L 3.5 Vol. sample (ml) 15 Vol. dilution (ml) 285 BOD (mg/L) ?
Q# 02: H1 TH H2 Toe filter H1= 12m and H2 2m Calculate head loss and head available at red, blue, green, purple and orange points.
Heavy oil discharges from a pipe through a sharp-crested, 100-mm-diameter orifice having discharge coefficient of 0.63. (a) What is the coefficient of velocity? (b) What is the velocity (m/s) of oil jet? (c) What is the head loss (m) through the orifice? 250 Orifice 1 Pipe OIL (SG = 0.91) MERCURY (SG = 13.6) NOTE: easurements are in 'mm' 350
QI\ Choose the correct item (a, b, c) for each of the following statements: Statements 1 Porosity (n) = 2 Absorption (Abs) = V:/(Vs+Vv) Vv/(Vs+Vv) Vv/(Vs-Ve) (W sat -Wary) (W ary-W sat) (W sat-W ary) 100 /Wary * 100 /Wary * 100 /Waut 3 If RQD of a rock core run is 85% its quality described : In Point Load Test UCS = Fair Роor Good 4 24 * Is (50) 12 * Is (50) 36 Is (50) 5 If the Modulus ratio of an intact rock is 300, its class designed If the aperture of a discontinuity is 70mm, it is termed 7 The formula for computing shear strength of smooth surface is: 8 The formula for computing shear strength of rough surface is: 9 The formula for computing shear strength of rippled and then smoothed surface is: Moderately Moderately wide 6. Narrow narrow Th= ơn * tan(@) * Tr =C+ on tan(@,) Tp tan(p) *Tr = C+ 0n Tb= On tan(p) Tp = On tan(@p) tan(or) Th = ơn tan(ob) Tp = ơn tan(op) Tr =C+ On + tan(or) 10 If the interval between joints 40 cm, their spacing described: Moderately wide spaced Closely…
Ma E-Hearning sanvices SQU Libraries SQU Portal Attendance This course► 100 m R1 2.00 on R2 R3 R5 R4 R8 R7 R6 R9 -LLL Dry Cleaner J. Gas Station Oil UST R10 If aquifer hydraulic gradient, hydraulic conductivity and effective porosity are found to be 0.4, 0.33 m/day and 0.25 respectively, determine how long the Benzene have been in the aquifer (in years)? 1 year 365 days Answer Time left c
Please answer all questions. I will rate. Oil of specific gravity 0.80 and dynamic viscosity of 0.05 Pa-s flows at a rate of 100 lit/sec through a 80 m of 150 mm diamater pipe. If the head lost is 4m, determine the Note:Choices are given Reynolds number (13,581.22, 15,831.22, 18,351.22, 12,521.82) Maximum velocity in m/s (1.67, 7.61, 6.17, 71.6) Maximum shear stress in Pa (14.72, 21.74, 41.27, 17.42) Velocity 30 mm from the centerline of pipe in m/s (4.99, 5.99, 6.99, 3.99)
Mixing (non reacting fluids), Electric circuits. Problem#1 A large tank holds 300 gallons of brine solution with 40 pounds (lb) of salt. A concentration of 2 lb/gallon is pumped in a rate of 4 gal/min. The concentration leacving the tank is pumped put at a rate of 3 gal/min. How much salt is in the tank after 12 minutes? Answer: 126.12 lb of salt
9:10 1 1 4 7 +/- 2 5 8 Question 19 of 20 The hydroxide ion concentration in a solution of NaOH is 2.0 x 10-¹ M at 25 °C. What is the pH of this solution? . 3 60 9 O .5G Tap here or pull up for additional resources Submit XU x 100
Determine the preak point dosage of chlorine given the data below which was obtained from chlorination experiment. 5 6 7 Dosage(mg/L) Required Cl₂Cmg/L 0.2 0.45 1.05 2.75 4.5 5.15 6.03 1 2 3 4