A W 600 x 110 beam is supported by bearing plate 300mm x 200mm x 25mm on wall with a thickness of 300mm. Properties of W 600 x 110 beam d = 600mm br = 225 mm tr = 18 mm tw = 12 mm K = 36 mm f = 24 MPa fy = 248 MPa The allowable bearing stress is 0.35 fc', allowable bending stress is 0.75 Fy and allowable web yielding stress is 0.66 Fy. Determine the maximum reaction at the beam due to the allowable web yielding stress at a distance (N + 2.5K).

A W 600 x 110 beam is supported by bearing plate 300mm x 200mm x 25mm on wall with a thickness of 300mm. Properties of W 600 x 110 beam d = 600mm br = 225 mm tr = 18 mm tw = 12 mm K = 36 mm f = 24 MPa fy = 248 MPa The allowable bearing stress is 0.35 fc', allowable bending stress is 0.75 Fy and allowable web yielding stress is 0.66 Fy. Determine the maximum reaction at the beam due to the allowable web yielding stress at a distance (N + 2.5K).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

This is a mechanics of deformable bodies problem
please answer asap
In a steel flat plate a state of plane stress available. Calculate o, and principal stresses if 0₁-140 N/mm², p=0.25, 1₁,-40 N/mm², e,- -3.6 × 10 and E-2× 10³ N/mm².
Three plates are welded together to form the section shown. Dimensions of the cross section are b= 4.7 in., d = 14.1 in., a = 2.8 in., and t= 0.5 in. For a vertical shear force of V = 42 kips, determine the shear flow through the welded surface at B. B a b Answer: kip/in.
Thank you po
ASAP!!! NEED RIGHT COMPLETE SOLUTION !!!
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
a. Determine the maximum flexural compressive stress in the beam. Answer in MPa rounded-off to 3 decimal places. b. Determine the maximum flexural tensile stress in the beam. Answer in MPa rounded off to/3 decimal places
32 H.W tind longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal Bessure is 0.9 Ma and thickness of Wall is 6.4 mm? Ansi é =42.19 MPa + F= 62.8 Ma Also find ?5067 0.6m 0.6m
A rectangular beam 200 mm wide has an effective depth of 350 mm. It is subjected to a bending moment of 24,000 Nm. The permissible stresses are c = 5 N/mm², t = 140 N/mm²; and m is 18. The required area of tensile reinforcement will be.
a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths