A voice message of 2 kHz is sampled at DM system for a rate nine times the Nyquest rate. The maximum signal amplitude is unity to avoid slop over load. Assuming the input signal amplitude is uniformly distributed in the range .of (-1,1) determine SNR SNR=148.1 SNR=190.2 SNR=180.3 SNR=140.5 SNR=160.4 SNR=160.5 SNR=150.9

A voice message of 2 kHz is sampled at DM system for a rate nine times the Nyquest rate. The maximum signal amplitude is unity to avoid slop over load. Assuming the input signal amplitude is uniformly distributed in the range .of (-1,1) determine SNR SNR=148.1 SNR=190.2 SNR=180.3 SNR=140.5 SNR=160.4 SNR=160.5 SNR=150.9

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A sinusoidal signal of 2 kHz frequency is applied at the input of a delta modulator with a step size of 0.1 volt. The sampling rate of the delta modulator is 20000 samples per second. What will be the maximum amplitude of the sinusoidal signal if there is no slope overload distortion?
What is the problem with AM signal when overmodulation occurs?
1)to VRMs value to generate a signal with a peak voltage of 10 V with a signal generator in a multisim program..................... must be entered. 2)) the frequency of the signal generator to produce a signal with a period of 10ms...................... must be entered as. What should come to the dotted line?
What is the purpose of low pass filtering a PWM source? To minimise noise produced by the PWM pulses To improve PWM efficiency To increase the amplitude of the PWM signal To rectify the PWM signal
B- An rate. analog signal having single frequency as 3 kHz is sampled with 5 kHz S Describe its frequency spectrum. What will be the output if the sampled signals a passed through a low-pass filter having cutoff frequency at 2.5 kHz? signal. are sent in the analog
Assuming that a certain ASM chart has 5 states, the size of each multiplexer required to implement this circuit using the multiplexer design approach should be: Select one: O a. Four to one. O b. Eight to one. O . None of the given. O d. Two to one.
(a) Plot the even and odd parts of the signal of Figure
A PM signal has a maximum allowed deviation of 17 kHz, and an actual deviation of 8 kHz. What is thepercentage modulation?
12- A DVM measure... a- peak value. b- RMS value. Average value. d- peak to peak value. 13 The study of energy distribution across the frequency spectrum of a given electrical signal is done by a Distortion meter b-wave analyzer.
Discussior partic enta tfrom the outPut signal fär half and trif lwave rectifer, calculate the Peak. ruot mean square crim.s) er and de values for Voltages. 2- Rind the freguency of indut and outfut Voltage signals 3-eXp laiN why you gut the positive Purts only of inPut Sigral of both clrcults.? inthe out Aut.
If a positive change in modulation signal level of 200 mV will cause a positive frequency deviation of 10 kHz, what I be the frequency deviation for a negative change of 100 mV in the level of the modulating signals? (Ans:-5kHz)
9. For the circuit shown in Figure Bl19a, Ve- 20V Rc 3k R = 10k 2 Wr VCE VBB=3V Figure B19a i) Sketch the DC load line in the Graph B19. ii) Calculate the Q point, if the zero signal base current is 50 µA and a -0.991. Mark the Q point in load line. D Focus 重 f8 fg f10 insort sc f12 & 近