A vertical column load, P = 600 kN, is applied to a rigid square concrete foundation. Thefoundation rests at a depth Df= 0.75 m on a uniform dense sand with the following properties:average modulus of elasticity, Es = 20,600 kN/m², and Poisson's ratio, µs = 0.3. Calculate therequired foundation dimensions if the allowable settlement under the center of the foundation is25mm.600 kNFoundation0.75 mВхвSoilHs = 0.3E, = 20, 600 kN/m²5.0 mRock

Given data: Rigid square concrete foundation. Column load (P) = 600kN Depth of foundation =0.75m…

A vertical column load, P = 600 kN, is applied to a rigid square concrete foundation. The foundation rests at a depth Df = 0.75 m on a uniform dense sand with the following properties: average modulus of elasticity, E, = 20,600 kN/m², and Poisson's ratio, µs = 0.3. Calculate the required foundation dimensions if the allowable settlement under the center of the foundation is 25mm. 600 kN Foundation Bx B Ao 0.75 m Soil Hs = 0.3 E, = 20, 600 kN/m² 5.0 m Rock

A vertical column load, P = 600 kN, is applied to a rigid square concrete foundation. The foundation rests at a depth Df = 0.75 m on a uniform dense sand with the following properties: average modulus of elasticity, E, = 20,600 kN/m², and Poisson's ratio, µs = 0.3. Calculate the required foundation dimensions if the allowable settlement under the center of the foundation is 25mm. 600 kN Foundation Bx B Ao 0.75 m Soil Hs = 0.3 E, = 20, 600 kN/m² 5.0 m Rock

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter17: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 17.5P

See similar textbooks

Similar questions

A foundation (Figure 1) transmits a stress of 100 kPa on the surface of a soil deposit. a. Evaluate increases of vertical stresses points A, B, and C at the depth of 2m and Sm (2 points) b. At what depth is the increase in vertical stress below A less than 10% of the surface stress? 6 m +2 m- A 2 m -4 m- Figure 1: Plan of foundation
Q 1) A concrete foundation rests on the surface of a soil mass. Determine the vertical stress increase at point A. 4 m 1 m 1.5 m PLAN 1.5 m Fondation Load 3000 KN 2 m SECTION A Soil
The initial principal stresses at a certain depth in a clay soil are 100 kPa on the horizontal plane and 50 kPa on the vertical plane. Construction of a surface foundation induces additional stresses consisting of a vertical stress of 45 kPa, a lateral stress of 20 kPa, and a counterclockwise (with respect to the horizontal plane) shear stressof 40 kPa. Determine the change shearing stress in kPa.
Problem II. The initial principal stresses at a certain depth in a clay soil are 100 kPa on the horizontal plane and 50 kPa on the vertical plane. Construction of a surface foundation induces additional stresses consisting of a vertical stress of 45 kPa, a lateral stress of 20 kPa, and a counterclockwise (with respect to the horizontal plane) shear stress of 40 kPa. a. Plot Mohr's circle (1) for the initial state of the soil and (2) after construction of the foundation. b. Determine the change in magnitude of the principal stresses. C. the change in maximum shear stress d. the change in orientation of the principal stress plane resulting from the construction of the foundation.
The initial principal stresses at a certain depth in a clay soil are 200 kPa on the horizontal plane and 100 kPa on the vertical plane. Construction of a surface foundation induces additional stresses consisting of a vertical stress of 45 kPa, a lateral (horizontal) stress of 20 kPa, and a counterclockwise (with respect to the horizontal plane) shear stress of 40 kPa. Plot Mohr's circle (1) for the initial state of the soil and (2) after construction of the foundation. Determine (a) the change in magnitude of the principal stress, (b) the change in maximum shear stress, and (c) the change in orientation of the principal stress plane resulting from the construction of the foundation.
A rectangular concrete slab, 3mx4m, rests on the surface of a soil layer as shown in the figure. The saturated clay has over consolidation ratio of 2, w=38%, and Cr=0.05. Determine the primary consolidation settlement of the clay. The load on the foundation is 2000OKN. Assume that 20% of voids in sand is air and porosity of sand is 0.43. Cc=0.28 Gs=2.65 4 m Fine sand 5 m Clay 2 m
= Figure 2 shows a rectangular shallow foundation. The foundation measures 1.5 m x3 m (B x L) in plan. The clay layer is normally consolidated with: Ce=0.27; He 3 m; e 0.92; average effective stress on the clay layer due to applied foundation load Ao=24 kN/m². Determine the primary consolidation settlement of the foundation. Sand Y = 16.5 kN/m³ Sand Yat 17.8 kN/m³ Normally consolidated clay Ysat 18.2 kN/m³ = 0.92; C = 0.27 170 kN/m² 1m 1.5 m Ground water table --- --- 15 m 3 m
A mat foundation, 15 m x 15 m, is made of reinforced concrete and to be supported by a three-layer soil profile, as shown. The mat is 1 m thick, and the average stress on the surface of the slab assessed from the structural engineering analysis is 75 kPa. (Unit weight of concrete = 23.58 kN/m^3) The 5-m thick sand layer immediately below the mat foundation has been compacted to standard Proctor specifications, most likely to optimum moisture content, which is why its moist density is given. (A) Determine the pre-construction effective stress at Point A (bottom of the clay layer). This is the in situ effective stress (overburden pressure) measured from the ground surface prior to the placement of the mat foundation. (B) Determine the vertical stress increase induced by the mat foundation at Point A using the “Influence Chart,” commonly referred to as the “Spider Web.” (C) Determine the vertical stress increase induced by the mat foundation at Point A using the “Stress Isobars.” (D)…
绘图编辑 3.12 For a strip foundation, the width is 1.2m, buried depth is 1.2m, the standard value of the load applied on the foundation F=155KN/m, the soil layer is distributed as follows: from the ground to the depth of 1.2m is the land fill, =18KN/m³; the depth in the range of 1.2~1.8m is silty clay, fak=155kPa, E,=8.1Mpa, y=19KN/m³; below the depth of 1.8m is the mucky clay, fak=102kPa, E,=2.7Mpa. Try to check the base pressure and the bearing capacity of the weak sub-layer. Ground F=155KN/m OLand fill 18KN/m³ 1.2m O Silty clay La-155kPa;E-8.1Mpa;y-19KN/m³ -0, 1.0 O Mucky clay -0, H1.0 Sak-102kPa;E,-2.7Mpa 1.2m
Estimate the increase in vertical stress at 0.5 m depth intervals, within the clay layer, below point A (See figure below). The foundation exerts a uniform vertical stress of 120 kPa at ground level. Using these values estimate the settlement due to the clay layer. (Hand in any graphs used) 5m 5m 2m 3m Very Dense Sand 2m 1.5m Clay E=3.5 MPa 2m Bedrock Soil profile A Plan of building 3m Soil profile and plan for Question 4 3m FA
In a site investigation for a large foundation project it is determined that there is a clay layer with capillary rise of 6.0 m above the groundwater table. What would be the effective stress and the pore pressure at point A located 2m above the groundwater table? Assume clay has Gs=2.70 and moisture content in capillary zone is 10%. Clay Gs=2.7, w=10% 10 m A. 2m
Problem 2. Determine the average (top, middle, and bottom) stress increase in the clay layer below the center of foundation due to foundation load of 50 tons. 50 ton (net load) Sand 100 Ib/ 4:5 t Groupdwater table 5 ft X 5 ft *Sand 122 lb/ft 3 ft A120 Ib/ft 0.7 C, = 0.25 10 ft 0,06 Preconsolidation pressure = 2000 lb/ft?