A vertical clean glass tube of uniform bore is to be used as a piezometer for measuring pressure of a liquid at a point. The liquid has a mass density of 1425 kg/m³ and a surface tension of 0.06 N/m in contact with air. If the capillary rise in the tube is not to exceed 2.0 mm, the required minimum diameter (in mm) of the tube is (Take angle of contact with glass is zero]

A vertical clean glass tube of uniform bore is to be used as a piezometer for measuring pressure of a liquid at a point. The liquid has a mass density of 1425 kg/m³ and a surface tension of 0.06 N/m in contact with air. If the capillary rise in the tube is not to exceed 2.0 mm, the required minimum diameter (in mm) of the tube is (Take angle of contact with glass is zero]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A capıllary glass tube of 0.1 mm internal diameter is immersed vertically in a beaker full of waten Assuming the tube to be perfectly clean and wet, determine the height of the capillary rise of water in the tube when the room tamp is 20°C. Given at 20°C unit weight of water = 0.9980 gm/cc and surface tension 72.8 dyne/cm. %3D
1. A clean circular glass tube is to be selected in the design of a manometer to measure the pressure of Kerosene . Specific gravity of kerosene 0.82 and surface tension of kerosene = 0.025 N/m. If the capillary rise is to be limited to 1 mm, the smallest diameter (cm) of the galss tube should be most nearly ... a) 1.35 b) 1.5 c) 1.75 d) 2.00
Weter flows up a tapered pipe (figure). A differential mercury manometer is attached to the pipe at Wand B. The pipe has a diameter of 200 mm at A and 100 mm at B, the point B being 1 m above the alot A. Obtain the deflection in the manometer corresponding to a discharge of 50 L/s. Neglect the friction in the pipe. Relative density of mercury 13.6. %D 100 mm 1 m 200 mm
an open tank when empty the water surface is at point A and the gaugefluid mercury shows a deflection of 20mm. Determine the new deflection of mercury when the tank is filled with water to B.
1. Describe the basic principles of dilatometer testing. 2. List the main component in dilatometer instruments ( 3. Derived the formula for coefficient of thermal expansion ( 4. Demonstrate how CTE can be measured from dilatometric curve Part 2: CO4 5. Give short description for each given Figure: ( 1.0- Parent glass Glass-ceramic 0.8 S0.6- 0.4- 0.2- 0.0- 200 400 600 800 Temperature (C) Figure 1: Dilatometric curve of parent glass and glass-ceramic sample 0.008 40Z60A 50Z50A 60Z40A 80Z70A 0.007 0.006 0.005 0.004 0.003 0.002 0.001 200 400 600 800 1000 1200 1400 Temperature (°C) Figure 2: Dilatometric curves for each sintered sample, containing different zircon- alumina weight proportions (%) '7/7P dL/Lo*10-6
Ex.1 Ans. A glass tube 0.25 mm in diameter contains a mercury column with water above the mercury. The temperature is 20°C at which the surface tension of mercury in contact with water is 0.037 kg()/m. What will be the capillary depression of the mercury? Take angle of contact 0= 130°. 3.02 cm
5) Determine the value of y in the manometer shown in the figure. 1 m Alr, 5 KPa Oil S = 0.8 3 m 1 m Water 0.5 ml Mercury 6) For a gage reading of -17.1 kPa, determine the (a) elevations of the liquids in the open piezometer columns E, Fand G and (b) the deflection of the mercury in the U-tube manometer neglecting the weight of air. Gage Air El. 15 m S0.70 El. 12 m Water El. 8 m S 1.6 B. 4m YMercury
For stearically stabilized system, weak flocculation occurs when thickness of absorbed layer is [x], particle radius is [y] and Hamakar constant is [z]. Chose the correct answer for x, y and z in the sentence above. Group of answer choices: x=large; y=small; z=large x=small; y=large; z=large x=large; y=small; z=small x=large; y=large; z=large x=large; y=large; z=large x=large; y=large; z=small
Answer the following questions: 1. A clean circular glass tube is to be selected in the design of a manometer to measure the pressure of Kerosene . Specific gravity of kerosene = 0.82 and surface tension of kerosene = 0.025 N/m. If the capillary rise is to be limited to 1 mm, the smallest diameter (cm) of the galss tube should be most nearly a) 1.35 b) 1.5 c) 1.75 d) 2.00 2. Both a gage and manometer are connected to a gas tank to measure its pressure. If the reading on the pressure gage is 80 kPa. The distance between the two fluid levels of the manometer h is ..... if the gage fluid in the manometer is a mercury (s 13.6); and h is if the gage fluid in the manometer is water. a) 0.4 m; 9m b) 0.9m; 4.3 m c) 6.213m; 0.7626 m d) 4.91m; 0.668m P= 80 kPa h = ? 3. A 50-ton, 6-m diameter hemispherical dome on a level surface is filled with water as shown in figure. An engineer claims that be can left this dome by attaching a long tube to the top and filling it with water. So, the required…
Calculate Fr and Yr using the prism method of solution
7 The capillary rise of water at 20°C in a clean glass tube, 1.0 mm in diameter is about (Assume surface tension of water at 20°C as 0.07 N/m)
flow of water in the below diagram is from point X to Y. The oil is in the e inverted U-tube manometer. The mercury is in the bottom of the manome ressure difference P -P in kPa?