A venturi meter with a throat diameter of 6 cm is fitted in a horizontal pipeline of 12 cm diameter with oil of specific gravity 0.88 flowing from left to the right. The difference in level in the two limbs of a mercury manometer connected to the tapping points read 12 cm and the connecting pipes are filled with the same oil. (a) If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. Determine the difference between the 2 gage pressure readings in kPa. (b) Determine the flow in m^3/s neglecting head losses.

Q: The maximum theoretical work obtainable, when a system interacts to equilibrium with a reference env...

A: This concept is based upon the concept of thermodynamics

Q: Name the parts of horizontal centrifugal pump. What are the curve that are normally visible on a pu...

A: Parts of Horizontal Centrifugal pump :  

Q: Compute for the force in members FH, GH, and GI (USE METHOD OF SECTIONS) *note : P = 8 kN

A:

Q: 8.5 The material of Problem 8.4 is subjected to an additional shearing stress of 10 MN/m. Determine ...

A: 8.6 Given: The direct stress in direction 1, σ = 45 MN/m^2 The direct stress in direction 2, σ = 75 ...

Q: A triangular window, with its top edge horizontal, is built in the side of a water tank. The window ...

A: Height of the window, H= 16 m Width of the window, B= 8 m Maximum force that a be hod by the window,...

Q: 1. Write down the derivation of formulas and describe each variable for each of the following discus...

A:

Q: If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. D...

A:

Q: A 64-lb weight suspended from a spring (spring constant is 200 lb/ft) is released from rest 0.4 ft b...

A:

Q: . Steam with a flow rate of 1360 kg/h enters an adiabatic nozzle (adiabatic, Q=0) at 1378 kPa, speci...

A:

Q: 1. Write the equation of motion for this system in matrix form. 2. Derive the characteristic equatio...

A:

Q: 8.7 At a point in a material under stress, there is a compressive stress of 200 MN/m and a shear str...

A:

Q: A thermocouple in the form of a long cylinder of 2 mm dia initially at 30°C is used to measure the t...

A:

Q: A steel shaft 1.4375 inches in diameter transmits 40 hp at 1400 rpm. Assuming a modulus of rigidity ...

A:

Q: Provide a general description of Induction Furnaces used in Industrial Manufacturing of Steel

A:

Q: The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an axia...

A: Given data: F=50 kN Need to determine the change in its length, the new height at section a-a, and t...

Q: Q3) There is a heat flux through a wall of 2250W/m. The same is dissipated to the surroundings by co...

A:

Q: What is the problem arise when design a pneumatics system with more than 1 cylinder and What are the...

A: the problem arises when designing a pneumatics system with more than 1 cylinder Because some pneumat...

Q: Find the vectors that satisfy the stated conditions. NOTE: Enter the exact answers using the provide...

A:

Q: Q10/ A large slab at 350°C suddenly has its surface exposed to convection 30°C with h = 80 W/m²K. De...

A:

Q: Electro-pneumatics Sequential Circuit Problem: Initial position all cylinder are retracted. Pressing...

A: Given : Cycle Operation: Cylinder A extend and hold the work piece. Cylinder B extend for 5 secs. Th...

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are e, = 0.40 ...

A: Stress in x-direction, σx = 63.3 MPa. Stress in y-direction, σy = 55.2 MPa.

Q: Does line AB intersect with parallel lines YZ and WX? Complete all views

A:                                                                      

Q: The angular velocity of the left disk is given as a function of time by o, = 4+0.2t rad/s. (a) and @...

A: (a) Angular velocities of B and C are ωB = 2.5 rad/sec and ωC = 1.25 rad/sec. (b) The angle through ...

Q: The MDF sheet shown in the figure below iscut by a laser pointer, which moves through the curved gro...

A: Given: Distance measured along the slot: →s=9t2-2t Hence velocity→v=dsdt=18t-2 And acceleration→a=dv...

Q: A steel cylindrical air receiver with 6.0 feet diameter and pressure load of 220 psi., design stress...

A: Answer: The bursting steam pressure of this air receiver is 1711.11 psi.

Q: A pipe transports 1962 N/s of water. The pipe tees into a 2"-diameter pipe and a 3"-diameter pipe. I...

A: Given   Velocity, V = 82 ft/s Diameter, d = 2 in                   = 0.166 ft Find  Flow rate

Q: 1. If the pulleys. veightless and frictionless, find the acceleration of body

A: Given:

Q: Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of “T” Nm....

A:

Q: value of spring constant K needed

A: Given;Uniform stiff rod of length,l=300 mm having a weight= 300 NIt is pivoted at one end and connec...

Q: A duct 0.40 m high and 0.80 m wide suspended from the ceiling in a corridor, makes a right angle tur...

A: Given data as per the question The inner radius = 0.2 m outer radius = 1.0 m The velocity of air in ...

Q: A bearing piece in the form of half of a hollow cylinder of 60 mm ID, 90 mm OD and 100 mm long is to...

A:

Q: 17. One ton of refrigeration effect is equal to how many Btu/hr.?

A: 1 Ton of refrigeration is the heat removal unit.

Q: STATICS AND STENGITH OF MATERIALS Question: Determine the moment of the force F about: a) Point A. 4...

A:

Q: The car A has a forward speed of 33.0 km/h and is accelerating at 2.3 m/s2 . Determine (a) a speed a...

A:

Q: Define the tools that must have during the Grinding Machine Operation.

A:

Q: Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, whi...

A: Find the diameter of the pipe at section 2.

Q: A submarine is rolling under seawater whose radius of gyration is 12 m and period of oscillation of ...

A:

Q: A steam power plant operates on the ideal Rankine cycle producing a net power output of 120 MW. The ...

A: Answer: ◆ The quality of steam entering the condenser is 74.10%. ◆ Qa = 3155.71 kJ/kg , Qr = 1795.96...

Q: b. A differential manometer is attached to pipe (p=10cm) which deposites a volume of 5 drums an hour...

A:

Q: 1- What is the benefit of the epicyclic gear train? Name s ome applications?

A: Epicyclic gear train :

Q: What are the factors upon which the frictional loss in a pipe depends? For friction loss, how i...

A: The frictional loss of pipe depends upon are density of fluid diameter of pipe, viscosity of fluid ,...

Q: Draw a graph showing the elasticity, flexibility, and brittleness property in terms of stress and st...

A:

Q: The car A has a forward speed of 33.0 km/h and is accelerating at 2.3 m/s2 . Determine (a) a speed a...

A:

Q: Liquid oxygen is stored in a thin-walled, spherical container 0.8 m in diameter, which is enclosed w...

A:

Q: Air standard Otto cycle have 10 compression ratio, if specific heat at constant volume ( CV)  increa...

A:    An Otto cycle is a simplified thermodynamic cycle that describes how a spark-ignition piston engi...

Q: 34. A pressurized tank contains saturated water. A frictionless valve on the pipe is now opened to d...

A: Solution: Given Data: P1=200 psiaL=4 ftD=2 in   Note: Po=600 psia

Q: A research team is interested in the difference between serum uric acid levels in patients with and ...

A: Soln For a population 1 Sample mean= 4.5 mg S1= 1 N1=12 For population 2 Mean = 3.4 S2= 1.5 N2= 15

Q: What is the problem arise when design a pneumatics system with more than 1 cylinder?and What are the...

A: Soln -The problem arise when we design a pneumatic systwm with more than one cylinder is the, pressu...

Q: An 11,300 kg/hr of water enters a cooling tower at 45°C. Atmospheric air at 16°C and 55% RH enters t...

A: Mass water evaporated =Mdryair×(w2-w1)w1=specific humidity at 16°C & 55% RHw2=specific humidity ...

Q: 8.9 The stresses across two mutually perpendicular planes at a point in an elastic body are 120 MN/m...

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.