A venturi meter is a device that is used for measuring the flow rate of a fluid within a pipe. Gas is flowing at speed vz through a horizontal section of pipe, as shown in the figure below, whose cross-sectional area is A2 = 0.0700 m2. The gas has a density of p = 1.30 kg/m. The venturi meter has a cross-sectional area of A1 = 0.0500 m2 and has been substituted for a section of the larger pipe. The pressure difference between the two sections is p2- P1 = 120 Pa. Find: (a) Find the speed vy of the gas in the larger, original pipe. (b) Find the speed vị in the venturi. (c) Find the volume flow rate O of the gas. Hi Lo P1 A2 2 A2 2 A1 Venturi meter

A venturi meter is a device that is used for measuring the flow rate of a fluid within a pipe. Gas is flowing at speed vz through a horizontal section of pipe, as shown in the figure below, whose cross-sectional area is A2 = 0.0700 m2. The gas has a density of p = 1.30 kg/m. The venturi meter has a cross-sectional area of A1 = 0.0500 m2 and has been substituted for a section of the larger pipe. The pressure difference between the two sections is p2- P1 = 120 Pa. Find: (a) Find the speed vy of the gas in the larger, original pipe. (b) Find the speed vị in the venturi. (c) Find the volume flow rate O of the gas. Hi Lo P1 A2 2 A2 2 A1 Venturi meter

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

b) The U-tube manometer can be used to determine pressure difference between two systems.This type of manometer is called a differential U-tube manometer. Consider the differentialmanometer connected to a pipe, as shown in Figure 1. Explain step by step on how you cancalculate the pressure difference between point A and B.
3. A differential manometer is attached to two tanks, as shown in figure. A) Calculate the difference in pressure of the two chamber B) Calculate the absolute pressure at A if the chamber B is open to atmosphere C) Calculate the pressure at the interface of the oil and mercury if the pressure at point A is 45 kPa Chamber A 1.1 m oil sg=0.89 0.30 m mercury Chamber B B tetrachloride sg= 1.59 0.8 m
Q- A mercury water manometer has a gauge difference of 0.8 m. The difference in pressure measured in metres of water is..
1. Describe the basic principles of dilatometer testing. 2. List the main component in dilatometer instruments ( 3. Derived the formula for coefficient of thermal expansion ( 4. Demonstrate how CTE can be measured from dilatometric curve Part 2: CO4 5. Give short description for each given Figure: ( 1.0- Parent glass Glass-ceramic 0.8 S0.6- 0.4- 0.2- 0.0- 200 400 600 800 Temperature (C) Figure 1: Dilatometric curve of parent glass and glass-ceramic sample 0.008 40Z60A 50Z50A 60Z40A 80Z70A 0.007 0.006 0.005 0.004 0.003 0.002 0.001 200 400 600 800 1000 1200 1400 Temperature (°C) Figure 2: Dilatometric curves for each sintered sample, containing different zircon- alumina weight proportions (%) '7/7P dL/Lo*10-6
Water flows steadily from a nozzle into a large tank as shown below. The water then flows from the tank as a jet of diameter d. (a) Using the piezometer tube shown, determine the flow rate through the nozzle. (b) Using the flow rate determine the value d if the water in the tank remains constant. Viscous effects are negligible.
A manometer consists of a tube of 0.5 inch in the inner diameter and an amount of mercury (SG Hg =13.55). On one side of the tube, oil (SG=1.4) was trapped, a bubble formed, and the fluid inside was stationary. The volume of the oil was 0.6 in^3 and the volume of the air was 0.2 in^3. Now, the oil and bubble are removed. The pressure change across the air bubble is negligible and any curvature on the bubble surface can be neglected in calculating the volumes. Determine how much the mercury height rises (i.e. h 4 -h 2 ).
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
An object with a shape of a cube with 280mm on each side, and weighing 425N is lowered into a tank containing a layer of water over a layer of mercury. a) Determine the position of the bottom block (height if the block submerged in mercury) above the mercury, when it has reached the equilibrium, in mm. b. Determine the position (height) of the top of the block above the mercury, when it has reached equilibrium in m.* c. Determine the position of the block below the water surface if the water surface is 300mm above the mercury layer in mm.
1. In the figure shown: a) Determine the centroidal distance (ỹ) from the X-Axis b) Determine the moment of inertia at the neutral axis. A 75 mm 100 mm A A B B
Which cross-section from the list below has a higher area moment of inertia about the centroidal axis? a.Solid circle of 30 mm diameter b. square with 30 mm side length c. Tube with outer diameter 30 mm and inner diameter 20 mm d. None of the above
Radius of a right circular cylinder is measured with an error of at most 5%, and the height is measured with an error of at most 9%. (i) Solve the maximum possible percentage error in the volume calculated from these measurements.
1 Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in FigureQ1 (a), can float on water at 20 °C due to the effect of surface tension. The density ofthe aluminum block is 2700 kg/m3. Determine the contact angle. 2. A solid alloy cylinder having a diameter of 6.48 cm slides downward at a terminalvelocity of V through a vertical pipe. The downward motion is resisted by an oil filmbetween the piston and the pipe wall. Determine the oil viscosity when the velocityV is 5 m/s. The inner diameter of the vertical pipe is 6.5 cm, and the alloy density is3500 kg/m3.