A vehicle with a weight of 1200 kg is initially at rest on an inclined surface of 10° (facing uphill). Assume that the friction coefficient in between the friction surfaces at the clutch is 0.3 and the maximum normal force is 1000 N. If the engine torque at the idle speed is 100 Nm, the first gear and axle drive ratios are both 3, would it be possible for this vehicle to start moving? Assume the tire radius as o.3 m. Explain your answer clearly.

A vehicle with a weight of 1200 kg is initially at rest on an inclined surface of 10° (facing uphill). Assume that the friction coefficient in between the friction surfaces at the clutch is 0.3 and the maximum normal force is 1000 N. If the engine torque at the idle speed is 100 Nm, the first gear and axle drive ratios are both 3, would it be possible for this vehicle to start moving? Assume the tire radius as o.3 m. Explain your answer clearly.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A sprinter practicing for the 200-m dash accelerates uniformly from rest at A and reaches a top speed of 36 km/h at the 76-m mark. He then maintains this speed for the next 61 meters before uniformly slowing to a final speed of 31 km/h at the finish line. Determine the maximum horizontal acceleration which the sprinter experiences during the run. Where does this maximum acceleration value occur? Part 1 Answers: (a) al- Finish line Calculate (a) the magnitude of the tangential acceleration near start of the race and (b) the magnitude of the tangential acceleration near the end of the race. (b) lal- i 0.658 i 0.205 m/s² 39.9 m m/s² A Save for Later Last saved 12 minutes ago. Saved work will be auto-submitted on the due date. Auto- submission can take up to 10 minutes. Attempts: 0 of 3 used Submit Answer Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above.
Draw the 1st and 3rd Angle Orthographic sketch of the following part:
How did you get 4/5 and 3/5?
Please provide more details for question b and c. thank you
A machinist in a maintenance shop made a 32 tooth gear 14 ½ degree pressure angle and 8 diametral pitch. Calculate the whole depth (Wd) NOTE: Place your answer in 4 decimal places, example; 0.4321
Please the answer provided is not clear, some words and letters not clear, can you please type the answer or write clearly so that I can see
Please answer 3, 4, 5, 6, 8, 9, 10, 12 1 is 0, 2 is 0, 7 is point A, 11 is 2. I included a picture of someone who solved but they were mostly incorrect. Please do not answer if the solution set I provided with the incorrect answers was you. I appreciate the attempt, but the solutions for 3, 4, 5, 6, 8, 9, 10, 12 were marked wrong, so unless you have different answers, please do not submit the same incorrect solution set. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the mass center G is set as the origin (datum), the gravitational…
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
! Draw a sketch of the above drawing in A3 (or two A4 paper taped together).
None
Orthographics: Add missing lines and complete any missing views. Draw the isometric