Answered: A vehicle was moving with tractive…

A vehicle was moving with tractive force of 70 kN and then turned on curve having turning angle 60°. The percentage of tractive force lost due to turning will be

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: One vehicle is following another on a two-lane, two-way highway at night according to the…

A: Given, V = 60 mph L = 20 ft t = 1.25 sec NOTE : As per guidelines, first question is required to…

Q: A truck travels along a straight, level road at the speed of 79ft/sec. when the driver is forced to…

Q: Determine the braking distance downhill and the percent grade of the highway at that section of the…

A: Velocity (V)= 55 mph Coefficient of friction = 0.30lets say breaking distance when driving uphill =…

Q: A highway curve of 120 m radius is banked to give equal wheel reactions for a speed of 48 kph. If…

A: The given data is as follows: Radius of curve=120 mSpeed to give equal wheel reactions=48…

Q: The 5-Mg truck and 2-Mg car are traveling with the free-rolling velocities of 37 km/h and 13 km/h,…

Q: One of the two motor vehicles is moving up the ramp at 90 km / h on a road with a slope of 3%, the…

A: It is required to find the shortest distance to avoid collision by breaking.

Q: The car is traveling at a speed of 75 mi/hr as it approaches point A. Beginning at A, the car…

A: Speed = 75 mil/hrdecelerates = 7.4 ft/s2 (upto B) =3.7 ft/s2 (after B)

Q: If a typical heavy truck (140 lb/hp or85 kg/kW) enters a 4% grade with an initial speed of 60 mph…

A: Weight/power ratioGradeDistanceTo find: Speed of the truck at the top of the hill.

Q: A vehicle weighing 2000-lb is traveling 30 mph at 5% upgrade with rate of 6 ft/sec². The vehicle has…

A: solution: Given: vehicle weight = 2000 lb. speed = 30 mph grade = +5% acceleration rate = 6ft/sec2…

Q: Question 2 A road is being designed for a speed of 110 km/hr on a horizontal curve with a super…

A: Given- Speed V=110 km/hr, Super-elevation e=8%=0.08, f=0.10, Minimum radius of the curve R=?

Q: A roadway is being designed for a speed of 60 mi/h. At one horizontal curve, it is known that the…

Q: 2.32 A driver is traveling at 52 mi/h on a wet road. An object is spotted on the road 415 ft ahead…

Q: 3. Drivers must slow from 70 mph to 40 mph to negotiate a severe curve on a rural highway. A warning…

Q: The allowable design speed for a highway is 100 km/h. Calculate the ruling radius of the horizontal…

A: Given: Design speed of highway, V = 100 km/h Super elevation, e = 0.10 Coefficient of friction, f =…

Q: car is traveling downhill on a suburban road with a grade of 4% at a speed of 35 mph. Determine the…

Q: A vehicle transverses a superelevated curve at 52 kph. If the radius of the curve is 64 meters, and…

Q: Determine the maximum speed in kph that a car could run around a 6-degree curve if the impact factor…

Q: Determine the impact factor for a highway curve having a radius of 1,997 ft and maximum design speed…

Q: A car is traveling on a -4.20% grade for a design speed of 90 kph. Coefficient of friction between…

A: Given Velocity= 90 kph Coefficient of friction= 0.33 Reaction time= 2.5 sec

Q: car travels at a costants speed of 100kph when its initial position is 400m measured horizontally…

Q: The rated speed of a highway curve of 300-ft radius is 40 mph. If the coefficient of friction…

A: Given data Radius of curve (R) = 300 ft Coefficient of friction (f) = 0.6 Rated speed of vehicle…

Q: 2-A motorist travelling at 100 km/h on a highway needs to take the next exit, which has a speed…

Q: horizontal. The center of gravity of the car is located 0.80m above the roadway and the distance…

Q: The car is traveling at a speed of 76 mi/hr as it approaches point A. Beginning at A, the car…

A: Given:- The speed of the car as it approaches point A = 76 mi/hr The car decelerates at a constant…

Q: The rated speed of a highway curve of 200 ft radius is 40 mph. If the coefficient of friction…

Q: The car is traveling at a speed of 67 mi/hr as it approaches point A. Beginning at A, the car…

Q: A vehicle is moving at a speed of 10OKPH along an inclined surface having a slope of 7%. If the…

A: Given Speed,V=100KPH Slope,g=7%=0.07 Coefficient of friction,f=0.34 To find ,breaking distance (d)

Q: A vehicle travels along a curve of radius 150 m banked at an angle of 15°. If the static coefficient…

A: Given that: Radius of curve, R=150mbanking of curve, θ=15°Coefficient…

Q: Situation 04. A car is entering a curve of radius 190m with a velocity of 165kph. Determine the…

Q: (1) The rated speed of a highway curve of 100m radius is 65kph. If the coefficient of friction…

A: For no skidding V2/(gR) < f

Q: e radius of cu wers limit their e lateral accele

Q: The design speed of a multilane highway is 70 mi/h. Determine the following. Note: The term a…

A: Step 1:Step 2:Step 3: Step 4:

Q: 2. The rated speed of a banked highway curve of 250-meter radius is 60 km/hr. If the coefficient of…

Concept explainers

Intersection Design

An intersection is a location where two or more roads or railways meet or join. The traffic movement is controlled at the intersection that depends on its design and type. It governs the operation, efficiency, speed, capacity, and safety of the highways, airways, and railways. The movement of the pedestrian causes hazards and delays at the intersection.

Question

A vehicle was moving with tractive force
of 70 kN and then turned on curve having
turning angle 60°. The percentage of tractive
force lost due to turning will be

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q- Determine the minimum non-passing sight distance that should be provided for a vehicle coming down a 6% gradient. Given that- design speed V=56 kmph Reaction time t=2 s Coefficient of friction f=0.5
What will be the non-passing sight distance on a highway for a design speed of 100 kmph when its ascending gradient is 2%? Assume coefficient of friction as 0.7 and brake efficiency as 50%.
The rated speed of a 200-meter banked highway curve is 50 km per hour. the radius of the highway curve is 250 meters and the coefficient of friction between the tires and the road surface is 0.50. What is the maximum speed at which the vehicle can round the curve without skidding? Express your answer in km per hour.
A traffic stream is moving at a steady state when entering a mountain grade. Upon entering the grade, the speed, density and flow are 72 km/h, 25 veh/km and 1800 veh/hr respectively. On the grade, a truck drops to a speed of 15 km/h causing traffic to bunch up to a density of 85 veh/km. When the truck pulls over, traffic accelerates to the maximum flow until steady state flow conditions resume. Calculate (a) the flow of traffic behind the truck on the mountain grade (b) the jam density and free flow speed for this road (c) the density and speed when traffic resumes a steady state flow (d) the maximum flow
A car is traveling at a speed of 100 ft/s which accelerates 12 ft/s2. The perception reaction time for the driver is 2.40 s. If the maximum grade of the road is -3.7%, compute the following: a. Braking distance in meters b. Lag distance in meters
solve
A truck travels along a straight, level road at the speed of 76ft/sec. when the driver is forced to apply the breaks to avoid an accident. If the truck undergoes a constant deceleration of 6ft/sec2, how far does the truck travel before coming to a complete stop?
A 4200 lb. automobile is traveling on a curve having a radius of 900 ft. If the acceleration of the automobile is 6 ft/s2, determine the constant speed in mph at which the automobile is travelling. a) 45 b50 c) 66 Od) 75 e) 81
The car is traveling at a speed of 77 mi/hr as it approaches point A. Beginning at A, the car decelerates at a constant 7.1 ft/sec2 until it gets to point B, after which its constant rate of decrease of speed is 2.3 ft/sec as it rounds the interchange ramp. Determine the magnitude of the total car acceleration (a) just before it gets to B, (b) just after it passes B, and (c) at point C. 220 B 372' Answers: (a) Just before B, a = ft/sec? (b) Just after B, a = ft/sec2 (c) At C, ft/sec2 =
The rated speed of a highway curve of 60m. radius is 50Kph. If the coefficient of friction between the tires and the road is 0.60, What is the maximum speed at which a car can round the curve without skidding?