A valve to a solid tank with a volume of 0.5 m3, initially hollow, well insulated The steam line at 480 °C  and 10 MPa has been connected. After the valve is opened, the tank Steam was sent in until the pressure was 10 MPa and the valve was closed. a) Calculate the final temperature of the steam in the tank. b) Why is the temperature you found in item a different from the temperature of the steam line?

Q: Q2 / Heat is transferred from a tank of water in a refrigerator at(OC) degrees to a tank of boiling…

A: GivenT1=0oC=273KT2=100oC=373KQ2=2254 kJ

Q: A diesel engine powers a boat. The engine's cylinders each have a cut-off ratio (V3/V2) of 2 and the…

A:

Q: A drum type steam generator operate at 160 bars. 1260 kg of water goes down the downcomer 7.32 °C…

A: Given data as per question Pump efficiency =0.70 considering density of steam at 160 bar in…

Q: Helium at 660 K expands in a turbine to 369 K during which 84 kJ/kg of heat was lost to the…

A: Guven data :-  Helium gas  T1 = 660 k  T2 = 369 k  Q = 84 KJ/Kg Pressure = 6.0  Find :-  Actual…

Q: Lets see how the conditions of AIR change from HEATING: Starting Conditions: DB 70F and 40% RH Final…

A: For Heating:

Q: Example 4-2 :A rigid tank of 1 m' contains nitrogen gas at 600 kPa, 400 K. By mistake someone lets…

A:

Q: 100 kg of water is heated from 10°C to 100 o C in a square container that is 0.5 meters wide by 0.5…

A:

Q: An Aluminum ball at 42 °C is dropped in a pot containing water at 42°C. The heat will Select one: O…

A: option (d) . not flow from aluminum ball to water or from water to aluminium ball

Q: The valve opens and the system comes to thermal equilibrium with the environment at 15oC. Find it in…

A:

Q: igeration is refrigera L0.P. if (i) th constant pre

A: C . O . P of the system    C .O . P = h1 - h6h2 - h1         Enthalpy h1 = 180.88 KJ/kg As the…

Q: Question 1- Steam expands in a steam turbine steadily at a rate of 32,000 kg/h, that enters the…

A: Given that, steam mass flow rate ,m˙=32000 kg/h At the turbine inlet , the pressure P1=7MPa the…

Q: 3.00 molesof an ideal gas expands irreversibly from a pressure of 2.4 bars to a pressure of 0.15…

A: The data given is, Number of moles, n = 3 moles Temperature, T = 300 K Initial pressure, P1 = 2.4…

Q: The air entering the turbine with 1200 K and 1200 kPa expands to 100 kPa pressure in two stages.…

A: Given Data Turbine Inlet:1200 K Two stage expansion process P1=1200 kPa, P2=350 kPa, P4=100 kPa

Q: 3) Gas is contained in a vertical piston-cylinder apparatus as shown below. The piston is fixed to a…

A:

Q: The power requirement of a 3-stage compressor (in kW, two decimal places) in order to supply air at…

A: To Find : The actual power requirement. Given :  The temperature is T=20°C. The discharge is Q=250…

Q: air form the dischard of a compressor enters 1 m3 storage tank. the initial air pressure in the tank…

A:

Q: interpolations/extrapolations: NO Calculator Technique and Applications. 1. Five kilo of water…

A: As per the guidelines of BARTLEBY we are subjected to solve only one question at a time. Please…

Q: 21: Steam at a pressure of 28kpa is passed into a condenser and it leaes as condensate at…

A:

Q: Q2: In an evaporator of a refrigerator, the refrigerant evaporates at (-20 °C) over the tubes. Water…

A:

Q: 2-[30P] A well-insulated tank contains air at 110 kPa and 40 °C with the isolation valve closed. We…

A: Given Data, P1 = Initial pressure of air inside the tank = 110 KPa T1 = Initial temperature of the…

Q: Four different streams of water enter a mixing chamber, as shown in the figure Each streams is at a…

A: Given data: Four different streams of water, all at 300 kPa pressure and equal flow rate of 1 (kg/s)…

Q: Two rigid tanks are filled with water. Tank A is 0.2 m' at 200 kPa, 150 °C and tank B is 0.3 m at…

A: Given that, Volume of tank A is, VA=0.2 m3Pressure in tank A is, PA=200 kPa,Temerature in tank A is,…

Q: 8. Determine the specific volume of steam at 6 MPa using the steam tables for the following…

A: as per guidelines we are supposed to answer only first three parts of a solution

Q: etely. Successive blurred Digit show

A:

Q: SET B: Five liters of air initially at 550K and 450 kPa is used in a Carnot engine and expanded to…

A:

Q: As part of a processing of biofuels, water is pumped into a circular tank with a diameter D₁, as…

A: For solution refer below images.

Q: Helium is to be compre kPa and 228 K to 440 k

A:

Q: Steam leaves an industrial boiler at 645.3kPa and 151.2°C. A portion of the steam is fed through a…

A: Given Data: Calorimeter's steam temperature, T2= 113.8°C Steam pressure at boiler exit, P1=645.3…

Q: to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for…

A:

Q: Solve the following problems and sketch the schematic diagram describing the system. Show pertinent…

A:

Q: A piston - cylinder system is filled with air. Initially, the air is at 489 kPa and 26\deg C. The…

A:

Q: ruptures and the water comes to a uniform state at 200°C. What is the final pressure? Find the work…

A:

Q: 17 kg of saturated water at a temperature of 34 degrees Celsius is heated to become wet steam…

A:

Q: You went inside a closed room occupied with several people. You noticed that despite the number of…

A: The fan described in the question is called a Misting fan. Here there is a container like structure…

Q: Assumption: We are assuming that the P(bar) of saturation is at 0.1 for our steam tables

A: Given: The streamer creates the steam at a pressure of 0.1 bar from 100 to 450 oC. and the mass flow…

Q: wolume displacement rato

A: Given data; C=0.03γ=1.15v1=0.1089 m3/kg Acc. to question; Capacity:  Q=2 tons=2×3.5 kW=7 kW P1=1.50…

Q: Container is filled with water. The total volume is 5 m^3. 1% of the volume is saturated liquid and…

A: Given data: The total volume of the container is, v=5 m3. The pressure within the container is,…

Q: b) Elaborate the response of pressure to the reservoir fluid properties using suitable equation.

A: Introduction: Fluid properties in a reservoir may be vary from space to space and from time to time.…

Q: Question: You have 10 kg of water at -15°C. You wish to heat it in an insulated box with a heater to…

A: For the solution refer below images.

Q: pressure cooker has the lid screwed in tight. A small opening with A= 0.0075 in^2 is covered with a…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.