LE424QUESTION 3a) Using resistor nearest preferred values (NPV), design a network as shown in FigureQ3a if Vcc = 25 V, Vc = 10 V, Ica = 3 mA and IcSATURATION) = 1.5lco. Determine thevalues of RB, Rc, and RE and state all assumptions made.VccloRcRBovcVoCoVioB = 100REZoFigure Q3a b) Draw the small signal AC equivalent circuit for the network shown in Figure Q3bconsidering r.= rce= 00 and determine the value of:i)le and VCEle and reii)ii)the input impedance, Ziiv)the output impedance, Z.v)voltage gain, Av = VoVvi)the current gain, A l/li25VRc=1KR1=100KCoo VoV -B=100R2=22KZiFigure Q3b

As per honour code , experts are advised to answer first question for multiple questions given.…

a) Using resistor nearest preferred values (NPV), design a network as shown in Figure Q3a if Vcc = 25 V, Vc = 10 V, Ica = 3 mA and IaSATURATION) = 1.5lco. Determine the values of RB, Rc, and RE and state all assumptions made. Vcc Rc Rs Vo Vi o Co B = 100 RE Zo ZI Figure Q3a

a) Using resistor nearest preferred values (NPV), design a network as shown in Figure Q3a if Vcc = 25 V, Vc = 10 V, Ica = 3 mA and IaSATURATION) = 1.5lco. Determine the values of RB, Rc, and RE and state all assumptions made. Vcc Rc Rs Vo Vi o Co B = 100 RE Zo ZI Figure Q3a

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: V1 R1 kN I1 D1 R3 kN 13 Vo V2 R2 kN D2

A: Note: Since you have posted a question with multiple subparts, we will solve the first three…

Q: The platinum RTD has been connected to the wheatstone bridge circuit represented by R3 with Vin =…

Q: A module with 40 cells has an idealized, rectangular I-V curve with ISC = 4 A and VOC = 20 V. If a…

A: Number of cells in modules, The open circuit voltage, The resistance of each cell in parallel, The…

Q: Question2: Calculate I, and the current I for V-0.73v for a pn junction for which N-1017/cm',…

Q: Analyse the circuit in Figure Q3(a) by using 3 different silicon diode models to determine the value…

A: Given data, Forward dynamic resistance of diode, r'd=10 Ω

Q: Calculate the junction capacitance of a silicon pn junction at T = 300 K with doping concentrations…

Q: Q3. * Calculate the junction capacitance of a silicon pn junction at T = 300 K with doping…

Q: V1 R1 Da S Hill Db KH R2 + V3 I Given that R1-2k, R2=1k, and Da and Db are Si Diodes: a. When will…

A: In this question, We need to determine the Voltage V1 if diodes are conduct? We are solving this…

Q: Q2. All pn diodes shown below have a voltage drop of 0.3 V when they are "ON". +4V DIA 李5k2 D2 VOUT…

Q: Q3. Determine the minimum and maximum values of the load current for which the Zener below will…

Q: H.W: For the network shown in figure below, determine : 1. The current I using ((KCL). 2. The source…

Q: Consider the following circuit with Vs(t) = 2.0+ 0.02 sin(2100t) V, R₁ = R₂= 25 2, Idc = 1mA, Vdc =…

A: The objective of this question is to analyze a circuit with a diode under both DC and AC conditions.…

Q: The two Zener diodes ofF FiG below have neglig;ble forwarod drops, and both regulate at Constant Vz…

Q: (a) Plot the load line and ﬁnd the Q-point for the diode circuit shown in P3.53 if V = 5 V and R…

A: Given data: V = 5 V R =10 kΩ a) Apply KVL in the given circuit, For VD Put ID = 0,

Q: (B). Find the effective resistance Rin of the network shown in Figure (2) below. Consider that each…

A: The given circuit is

Q: A given monocrystalline silicon solar cell has the following specifications: Isc=5 A and Voc=0.6 V.…

A: Given that Voc=0.6VISC=5An=25 Although, All are connected in series Hence,…

Q: İn the circuit above, plot İx and İr1 as a function of Vx for two cases : Vx=-1.25V and VB=+1.5V.

A: Given: A circuit, To do: We have to plot Ix and IR1 as function of Vx. a) When VB= -1.25 V, b)…

Q: Q7. In Figure X shown below: a. Identify the biasing configuration b. Draw the equilvalent circult…

A: Given circuit is belongs to mosfet circui

Q: From the circuit below, 1.) Determine the current IRL flowing through the resistor RL. 2.)…

A: Given circuit:

Q: R3 D1 RL V3 Figure 3. Zener diode with a load resistor. Let V3 = 15 V, R3 = 430 ohms. %3D 1. Now,…

A: In the question, Determine the lowest value of RL such that the voltage drops across RL is the…

Q: (a) Plot the load line and ﬁnd the Q-point for the diode circuit as shown in P3.53 if V = 10 V and R…

A: Part (a): The current flowing through the diode is determined as:

Q: a) Using the circuit in the figure, the experimenter calculates the internal resistance R. of the…

A: Explanation: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: derning the cirčuit in the following figure, if V1 varies between -20 V and 0 V and Vb%3D5V, then…

A: Find the current in the voltage V1 if the voltage V1 varry -20V to 0V Vb= 5V

Q: In a two-terminal network, the open-circuit voltage measured at the given terminals by an electronic…

A: Given data- 2 terminal network, Open circuit voltage- Voc=100 V, Ammeter reading I=5 A, Load…

Q: Draw the equivalent circuit of pv cell

A: A unique type of semiconductor diode called a photovoltaic cell produces direct current from visible…

Q: Question2: A pn junction uses NA = 2x1016 /cm and ND=9x1015 /cm. Determine the built-in %3D voltage…

A: Doping concentration of PN junction given. Find the built up voltage at 600K temperature. ? Let's…

Q: X(2)→O do -b, Figc2). H. Ws Prove that the system in Fig (2) has: -1 H(2)= ao+a, 2 I+b, é

A: We need to find out transfer function

Q: A certain nonlinear device has i D = v D 3 /8. Sketch iD versus vD to scale for vD ranging from -2 V…

A: Given: iD=vD38, Range of vD= -2 V to +2 V

Q: Vs(t) D2 Vout + DA D3 17 W RL D1

A: Given the circuit, • Diode D3 is damaged so that it is always open circuit regardless of the applied…

Q: Izl min=lmA ZDi Vzl=3.1V Iz2 min.=1.5mA The maximum power of each of the three zener diodes in the…

Q: In a two-terminal network, the open-circuit voltage measured at the given terminals by an electronic…

A: We need to find out the current through load for given circuit .

Q: In a two-terminal network, the open-circuit voltage measured at the given terminals by an electronic…

Q: R3 = 350 N and R4 = 200 N are connected such that the parallel combination of R, and R2 is connected…

Q: P4 A 6V battey, delirers loMA to thvee resistors in paralkel, R -1kr, R2 =2K2,R3%=Rx-. Caleulates a)…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: A VBE multiplier (see Figure 1) is designed with equal resistances for operation at bias current of…

A: As given β=∞ that means the base current of the BJT in the circuit is zero. Also, VBE=0.7 V At…

Q: Six group of batteries are in parallel. Each group as 10 cells connected in series, each has an…

A: We need to find out the equivalent resistance and emf for given battary combination , we need to…

Q: Q3. * Calculate the junction capacitance of a silicon pn junction at T = 300 K with doping…

Q: In a two-terminal network, the open-circuit voltage measured at the given terminals by an electronic…

A: Given, open circuit voltage is, Voc=100 V Short circuit current is, Isc=5 A load resister =80 ohms.…

Q: Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R₁ =…

Q: Vs(t) D2 Vout W RL D₁ + DA + D3

A: Given the following information of below circuit; Diode D3 is damaged so that it is always open…

Q: With a D'Arsonval movement with 200 internal resistance and 100 mA FSD current, it is required to…

A: Given information are as

Q: A PMMC instrument has internal resistance of 0.66 kn and gives full scale deflection for 30 mA. The…

A: To use voltmeter as a multi range voltmeter we have to add series resistor.

Q: R₁ R₂ R₂ R3 www CQ3.01 Given: R₁ = 1729720 (Ohms) R₂ = 2532062 (Ohms) R3 = 435972 (Ohms) Find the…

Concept explainers

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.

Question

b) Draw the small signal AC equivalent circuit for the network shown in Figure Q3b
considering r.= rce= 00 and determine the value of:
i)
le and VCE
le and re
ii)
ii)
the input impedance, Zi
iv)
the output impedance, Z.
v)
voltage gain, Av = VoV
vi)
the current gain, A l/li
25V
Rc=1K
R1=100K
Co
o Vo
V -
B=100
R2=22K
Zi
Figure Q3b

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1Z

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4) a) In figure given below, Ri=10 Q, R2=20 Q, and the ideal batteries have emfs Ɛi=20 V and Ez=50 V. What value of R3 results in no current through battery 1? ww R ww
Problem 1: Di and D2 are battery modeled diodes of 0.7 V. If 'V;’ is a sinusoidal signal with 1 kHz frequency and amplitude voltage of 40V, 1. Plot Vo, Ipi, and Ip2 versus 'V¡’ 2. Plot Vo versus time D1 D2 3 k2 9 k2 V; Vo 25 V 5 V
S3) Calculate the current IB, IC and voltage VCE in the circuit in the figure and examine whether it is conduction or not? (VBE=0,7V , β=80)
i.... will give upvote if correct
Determine Q-point for the diodes in the circuit given below using the ideal diode model where, R1 = 12.2 kΩ, R2 = 16 kΩ, and R3 = 14 kΩ. (Note: Label the diodes from left to right.)
Q7
Diode State (On or Off) ID VD D1 _mA _ V D2 _mA _V D3 _ mA _ V
Q1) Using suitable circuit analysis method, determine V1, V2, V3 and V4 of circuit in Figure Q1 below. V4 20 Q 10 Q V1 10 V2 10 Q 30 Q V3 4 A 20 Q Figure Q1
Pt A 6v battey, delivrers loMA to thvee resistors in faralkl, R, =1kr,R2 =2K2,R3=Rx- Calcalate: a) Current in b) Power dissipatiod by Rx and R,-[Anss 6mw, 36mn. c) Resistance ratio Rx/R--(Ans: 6/)- d) Current ratio Ii/Ix. Anst 6/4). Rx stheatis Ix Anss 1 mÁ)
estion 3: For the circuit given here, Write the expression for Vout in terms of the Vin, R1, R2 and R3. Vout? +8 V R₁ 1K R₂ 3.3K 1N5230B 4.7 V Zener D₁ www R3 1K +5 V For given values of Vin, the resistor values and zener diode rating, calculate value of Vout
Q3. * Calculate the junction capacitance of a silicon pn junction at T = 300 K with doping concentrations of Na = 10¹6cm-³and Na = 10¹5 cm-³. Assume that the intrinsic concentration n = 1.5 x 100 cm-3 and the reverse bias V, 5V Note/ Your answer -1.035 x 10-¹2F/cm e-16x 10-¹c
Calculate the equivalent resistances Rin of the following circuits. (The resistance value of the diodes in the conduction will be 0, the resistance value of the diodes in the insulation will be taken as infinity. R1=10ohm