A uniform 100-lb beam is held in a vertical position by a pin at its lower end and a cable at its upper end. A horizontal force (magnitude P) acts as shown in the figure. If P = 75 Ib, what is the magnitude of x-component of the force at the pin? Select one: 3,0n a. 69 Ib b. 47 Ib 5.0 n c. 75 Ib d. 28 Ib e. 54 Ib

A uniform 100-lb beam is held in a vertical position by a pin at its lower end and a cable at its upper end. A horizontal force (magnitude P) acts as shown in the figure. If P = 75 Ib, what is the magnitude of x-component of the force at the pin? Select one: 3,0n a. 69 Ib b. 47 Ib 5.0 n c. 75 Ib d. 28 Ib e. 54 Ib

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4/70 A force P is applied to the midpoint D of link BC. State the value of the couple M which would render (a) the horizontal force transmitted by pin B zero and (b) the vertical force transmitted by pin B zero. M R 45 B 30 Problem 4/70
The beam is supported by a pin at A, a spring having a stiffness at B, and a roller at C. Determine the deflection at B. EI is 40788045.2 kNm². a. 1.50 mm b. 0.404 mm c. 1.40 mm d. 0.912 mm
10 kip/ft 50 kip · ft A B 5 ft 5 ft The simply-supported beam above is subjected to a uniformly distributed load and couple moment, as shown. The beam is supported by a pin at A and roller at B. Which of the following best describes the shape of the shear diagram between point A and the midspan of the beam? a) zero b) constant c) linear d) parabolic e) cubic
110% Problem 2: For the step pulley shown, solve for the resultant of the non-concurrent forces applied on it. 2875N 1000N 300 40cm 25cm 5000N :-
A cable is used as a laundry washing line whose end points are fixed at A and B. The clothes on the line resemble -10 m: В y 5 m 4 m approximately a constant line load w = 72 N/m. Compute the maximal force in the line for a minimal distance of the line to the ground given by 3 m. Select the correct response: 747.94 N 581.73 N 1038.80 N 363.58 N
The force-couple system shown acts on a trapezoidal plate. a. Determine the value of M, if the system shown is equivalent to a single force acting at point C. b. The system shown is equivalent to a force-couple system consisting of R and M2 = 3000 kip-in clockwise. If M, in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD. 50 1YZ kips 10 in 1X in 10 in B 20 kips 35 kips 8X kips 2Y in M1 50 1YZ kips Parameters X = 7, Y = 8, Z = 4 1X in 17 in 2Y in 28 in 8X kips 1YZ kips 87 kips 184 kips 18 in
2/88 If the resultant of the forces shown passes through point A, determine the magnitude of the unknown tension T which acts on the braked pulley. 1600 N 275 N 0.5 1.8 m 1.5 m Im 300 N 1.25 m B 50 0.6 m T2 650 N
O O Y:00 أنت F= 5.2+35 Q5/ Compute the magnitude of force (F) and the vertical reaction at point (A) of cantilever beam where an inclined concentrated force vector has been applied at point (B) as shown in Figure 2 m Ans/ |F| = 6 Ay = 3 个

The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? i. 12500N ii. 10000N iii. 7500N iv. 22500N B. What is the value of the absolute maximum moment? i. 31250Nm ii. 20000Nm iii. 11250Nm iv. 22500Nm C. Reinforcing steel bars [shown by the bold lines] are used in the concrete beam in the lookout as shown in the diagram below, which of the following diagrams best shows the placements of these reinforcements? Why?
The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? i. 12500N ii. 10000N iii. 7500N iv. 22500N B. What is the value of the absolute maximum moment? i. 31250Nm ii. 20000Nm iii. 11250Nm iv. 22500Nm
The force-couple system shown acts on atrapezoidal plate. a. Determine thevalue of M, if the system shown is equivalent to a single force acting at point C. b. The system shown is equivalent to a force couple system consisting of R and M2= 3000 kip-in clockwise. If M, in this case is 120 kip-in counterclockwise, determine the point of action of the resultant force R along line CD. 50° 1YZ kips 10 in 1X in 10 in 20 kips 35 kips 8x kips 2Y in 5o 1YZ kips Parameters X = 7, Y = 3, Z = 7 1X in 17 in 23 in 87 kips 137 kips 2Y in 8x kips 1YZ kips 18 in
A rectangular reinforced concrete beam with width of 300 mm & effective depth of 600 mm is subjected to a service bending moment of 200 kN.m. The beam is reinforced with 4-32 mm diameter bars. n = 8. 1. Compute the distance kd? a. 246.33 mm b. 353.67 mm c. 170.33 mm d. 302.33 mm 2. Which of the following gives the moment of inertia about N. A.? a. 4173.81 x 106 mm⁴ b. 3471.81 x 106 mm⁴ c. 4371.81 x 106 mm⁴ d. 4713.81 x 106 mm⁴ 3. Which of the following most nearly gives the maximum stress in steel in Mpa? a. 100 b. 110 c. 120 d. 130