A two-seated airplane requires that both the pilot and the navigator have their seats-belts tightened before the plane can take off. However, it is desired that in case of solo flight (without the navigator) the state of navigator seat-belt should not have any effect on the take-off. Design a suitable switching circuit, and obtain the logic expression for the system,(Include an ignition switch in your design).

A two-seated airplane requires that both the pilot and the navigator have their seats-belts tightened before the plane can take off. However, it is desired that in case of solo flight (without the navigator) the state of navigator seat-belt should not have any effect on the take-off. Design a suitable switching circuit, and obtain the logic expression for the system,(Include an ignition switch in your design).

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
1. The synchronous finite state machine (FSM) with input X and output Z consisted of two D-flip-flops with positive edge triggering and asynchronous clear (Figure 1). The flip-flop input excitation and output forming logic were implemented with 2-to-1 multiplexers (note that in the multiplexer symbols data inputs DO are shown above inputs D1). Obtain the following: a) Excitation equations for flip-flop inputs (Q1*, Q0*) and the equation for output Z. b) Output type (Moore/Mealy). c) State table: next states (Q1*, Q0*) as functions of present states (Q1, QO) and X, show output Z values. d) State diagram: show output Z values. e) Output Z sequence for input sequence X = 1111110000. The flip-flops were cleared initially. f) An estimate of the maximum clock frequency for reliable operation. The setup time and D to Q propagation time are 6 and 55 ns, respectively. The multiplexer delays are 36 ns and 47 ns for Data and Select inputs, respectively. Assume a 10 ns delay for the inverter.…
a) In Assembly programming what is the functionality of the following instructions DECFSZ ВTESC MOVLW MOVWF goto b) A piece of code is required for a time critical activity. Should this be written in assembly language or C? Explain your answer. 5 Explain the difference between the (For) and (While) loops. Highlight the main components of the (For) loop that are required for its execution. Consider the following C program designed to run on a PIC 18F4455. int main(void) 2 { 1 double voltage; double current; double milliwatts; double energyUsed; double cummulativeEnergy = 0; while (1) { voltage=analogRead (VOLTAGE_PIN)*voltageScaleFactor; current=analogRead (CURRENT_PIN)*currentScaleFactor; milliwatts=voltage*current; energyUsed=milliWatts*0.5; cummulativeEnergy=cummulativeEnergy+energyUsed; 10 11 12 13 14 15 _delay_ms (500); 16 } 17 a) What is the role of the symbols "{" and "}" b) The code here is indented. Explain the importance of indentation N m 4 n Or 00 o A m
Q1. Design a 4-input, one output combinational logic circuit for the following input-output conditions: a) If the number of 1’s in inputs is more than or equal to 2 then the output is 1 ?. b) If the number of 1’s in inputs is less than 2 then the output is 0 ?.
Given a state machine with the following state transition table. Draw the circuit diagram, and give me the logical expressions.
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Review Questions Question [4] For the given sequential circuit: a. What type of state machine is this circuit and why? b. Determine the flip-flop input equations and the output equations from the circuit. c. Derive the next-state equation for each flip-flop from its input equations. d. Derive the State table. e. Derive the State Graph. Determine the state sequence and output sequence if the initial state is So and the input sequence is X= 01100 B B KA CK JA KB CK to Clock Clock X" X- X' A B'
The necessary condition for a fan motor to activate (to be logic “l”) is that at least three of the 4 motors named A, B, C, D, with which it works together (to be logic “l”). Design the logic circuit (logic circuit) expressing the activation of this fan motor according to SOP (minterm) using Karnaugh Method.Write the function obtained by Karnaugh Method (without further simplification of the function obtained from Karnaugh, that is, as obtained from Karnaugh) and draw the circuit of the function you obtained. Make sure that the circuit you have drawn is understandable, the function you have written, the truth table and the Karnaugh map are readable.
The control circuit functions to turn ON the light bulb whenever the binary inputs are even numbers between 1 and 15 in decimal. Other than that, the light bulb turns OFF. Design the logic control circuit of figure below. In your design, include: a)>The truth table deduced from the description. b)>The simplified output expression. c)>The logic control circuit using combinational logic gates. W Logic control X F Y• circuit > N
Q₁: Choose the correct answer ( 1. If the output of the FSM depends only on the current state, it is called a . a) Mealy machine (b) Moore machine c) Henry machine d) None of the above 2. Finite state machines are combinational logic systems. a) True False sequential losic system 3. A............ is simply a piece of conventional code that can be used within another circuit which allows the construction of hierarchical designs. C 4. PLAs were the most user configurable of the simple PLDs because Both AND and OR arrays were programmable b) The AND array was programmable, and the OR array was fixed c) The AND array was fixed, and the OR array was programmable d) Both the AND and OR arrays werefixed a) Library b) Components c) Packages d) Functions
Problem Description Material A and Material B are collected in a tank. These materials are mixed for a while. Mixed product is then drained out through Outlet valve. Implement this in PLC using Ladder Logic programming language. Problem Diagram Diagram of a mixing tank -Agitator Motor Material A Material B Inlet Valve 1 Inlet Valve 2 Level Material B☐ Level Material A Mixing Tank LLS Outlet Valve Mixed Product
Digital Logic Design Show the Diagrams, please as well. Must answer according to the Questions exactly.