A truck with axle loads of 20KN and 30KN on a wheel base of 2.5m rolls across a 5-m span. If the center of the 30 kN axle load and the resultant load  is at the center of the beam, calculate the reaction at the left support. a.30 kN  b.25 kN c.15 kN d. 20 kN calculate the reaction at the right support. a.30 kN  b.25 kN c.15 kN d. 20 kN

Q: Prob.11 Determine the largest weight of the oil drum that he floor crane can support without…

A: Given :

Q: A beam is used to support a concentrated load of 12 kN and a distributed load (w). The beam has the…

A: ∑MB=0 -12 x 3 - RC x 9 = 0 RC = -4 kN ↓ ∑V=0 RA + RC = 6 x 9 - 12 RA = 46 kN ↑ ∑MA=0 -MA + 6 x 9 x…

Q: A truck is moving along 20 m. Span of beam. The front axle load is 8 kN, the middle load is spaced…

A:

Q: A 7-meter simple beam has one of its supports at the left end and the other is placed 3m from the…

A:

Q: From the given beam: Determine the vertical reaction Ey at point E 12 kN 4 kN/m 2 kN/m 16 kN-m 8…

A:

Q: a = 3.2 m, b = 33.5 kN/m, c = 24 kN. ç kN b kN/m A BỊ DO "a" m 4 m 3 m FIGURE 2

A:

Q: A beam has a moment of inertia 500 x 10 mm* and a length of 8r and is able to carry a 90 kN load at…

A: As per guidelines we need to answer only first 3 subparts of questions so please repost rest…

Q: Situation 4: A truck with axle loads of 40 kN and 60 kN on a wheel base of 5 m rolls across a 10 m…

A:

Q: A cantilever beam is propped at the free end and carrying a uniform load of 400 kN/m throughout the…

A:

Q: A beam is loaded as shown in the given figure. 1. Which of the ff. gives the reaction R? a. 43…

A: We will find reaction and draw shear and moment diagram.

Q: A simple beam AB is loaded by two segments of uniform load and two horizontal and vertical forces…

A: The free body diagram of the beam is shown below:

Q: 3 m A 20° 20 kN M T1 10 mi T2 2 m D 4 m 4 m 2 m

A: To find tension in rod

Q: Three equal wheel loads of 30 kN each, separated by 2 m between each load, roll as a unit across a…

A: A moving load is acting of bridge span and it has been asked to determine maximum bending moment.…

Q: Calculate the maximum bending moment for the moving load of the bridge using the following data's.…

A: Moving load on bridge : Bridge is considered as a simply supported beam  In simply supported beam…

Q: A simple 10 m long beam can carry a uniform load of 10 kN/m. It also carries two point loads. a)…

A: Solution: Support reactions:                               RB = 50 kN ⇒                        RA =…

Q: 24 kN 5 kN 16 KN 16 kN 26 50 kN-m 100° В 35° A 1.6 m 2.2 m 2.4 m |1.2 ml 2.6 m A terrible driver has…

A:

Q: om A. Compute the vertical reaction at A.

A:

Q: 2. Compute the reactions of the fixed support at K.

A: Given:- A beam system having different loading on different beams To find:- Reactions of the fixed…

Q: A cantilever of uniform section is 3 m long. It is rigidly fixed at one end and is propped to the…

A:

Q: 3m 3m 1 5m o 3 kN/m The 100 mm thick concrete slab shown weighs 24 kN per cu. meter and is being…

A:

Q: A vertical load of 10 kN acts on a hinge located at a distance of L/4 from the roller support Q of a…

A:

Q: The mobile crane is symmetrically supported by two outriggers at A and two at B in order to relieve…

A: Mass 18 Mg and center of mass at G1, and boom has a mass of 1.8 Mg and a center of mass at G2.

Q: Which of the following most nearly gives the maximum bending moment? c. 162.00 kN-m d. 157.50 kN-m…

A: 10. Option- a 11. Option- d 12. Option-a

Q: Determine fixed support reaction . I will upvote Give fast answer

A: FBD :

Q: BY D Calculate the reactions at the supports in the opposite E beam and draw the shear forces…

A: To find support reaction and to draw SFD

Q: 4. Calculate the support reactions and plot the internal force diagrams for the following multi-span…

A:

Q: The beam is loaded as follows: ● Downward distributed load that varies in intensity from 10 N/m at…

A: Given: Required: Moment at fixed support Vertical reaction at fixed support Load diagram Note: as…

Q: maximum shear force and the maximum bending moment.

A:

Q: Situation 4: A truck with axle loads of 40 kN and 60 kN on a wheel base of 5 m rolls across a 10 m…

A:

Q: Three equal wheel loads of 50 kN each sperated by 2 m between each load roll as a unit across a…

A:

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A 15 kN; B = 25 kN, 2 m to the…

A:

Q: A 3 m-cantilever beam is subjected to a uniformly distributed load of 16 kN/m. Which of the…

A: To Determine moment at the midspan of the cantilever beam.

Q: Determine the magnitude of the force on the pin at A for the jib crane shown. The beam AB is a…

A:

Q: 3. The uniform girder AB has a mass of 8 Mg (Figure 3). Determine the internal axial, shear, and…

A:

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.