A transmission shaft is supported by bearings at A and D and loaded as shown in the figure. a. Find P required to achieve equilibrium. b. Find the reactions at the bearings. c. Sketch the V-M-T diagrams (Hint: You need to construct V and M for planes xy and xz).

A transmission shaft is supported by bearings at A and D and loaded as shown in the figure. a. Find P required to achieve equilibrium. b. Find the reactions at the bearings. c. Sketch the V-M-T diagrams (Hint: You need to construct V and M for planes xy and xz).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5.4 For the rigid frames shown in Figure P5-4, determine (1)the nodal displacements and rotation at node 4, (2) the reactions, and (3) the forces in each element. Then check equilibrium at node 4. E, A, and I are identical through all elements. 6m = Figure P5-4 -7.5 m- 6m 80 KN -7.5 m 12 m 9m E = 210 GPa A = 5 x 10-³ m² 1=3 x 104 m²
A crank shaft is operated as shown in the figure. A load F1 = 9.73 N is applied and the operator %3D dz applies a load P to counter. The system is in equilibrium and all of the bearings are perfectly dz aligned such that they do not produce moments on the rotating crank. The geometry is given by, w = 7.31 [m), dl = 9.69 m], d2 = 7.57 m). 6.14 (m), d5 = 3.7 (m), %3D d1 d3 = 9.87 (m), d4 %3D F2 and h1 4.4 (m), find the following: %3D F1 Part 1. Express the reaction forces exerted on the bar by the journal bearing at point B. Use the coordinate system shown in the diagram 10 5% 100% Submit [N] Part 2. Express the reaction forces exerted on the bar by the journal bearing at Point A. Use the coordinate system shown in the diagram. 5% 100% 10 Submit [N]
Question 2 A crank slider has a crank of length 0.04m and a coupler of length 0.08m as shown in the figure. The crank mass is 0.25 kg and is located at the center of a slender link (IG = 1/12*m*1²). The coupler is massless. The slider has a mass of 0.25 kg and a load of -10N in the i direction. Find the torque required to drive the mechanism and forces at O2 and B for a crank angle of 90° if the crank has a steady state rotation of 1000 RPM in the counterclockwise direction. А b = .08m m, = 0.0 I, = 0.0 В T, 0,, wz, a, 0, wz, a, 2' 3' 3' 0, F, = -10î N m, = 0.25 kg I, = 0
Force between A and B: 200lb Angle on D: 35 deg Angle on C: 50 deg
A simple structure is to be built to hold load at C as shown in Figure Q5. Body ABC is pin joint at wall A is regarded as a rigid body and is pin supported to rod BD at B. The respective dimensions are as shown in the figure. A support unit is to be connected by pin between point B and point D or point D' at the wall. a) Compare and analyze the two positions for the support unit not to fail by buckling when maximum load F is applied at C. Which position is the better choice between D and D' ? b) If load F is in opposite direction, what is the maximum load F that can be applied. (Properties of rod BD, E= 200GPA, G=77 GPa, v=0.3, o, = 250 MPa ) A 1.6m В 1.4m C 0.9m F 10mm 4mm D 0.8m 9. 15mm mm D' Crossection of Hollow Rod BD or BD'. ( 10mm x 15mm and 4mm x 9mm) Figure 05
5
2. Show detailed and complete solution with Free Body Diagram.
4 bar mechanism shown. Crank AB rotates counter clockwise. External force of 8.5 kN acting on link CD at Point P. Link BC makes 18 degree angle with the horizontal A) draw free body diagrams for link AB, BC, and CD B) write the static equilibrium equations for link CD C) if force applied to link CD (link 4) as a result of contact from link BC (link 3) is 2690.52N, calculate the horizontal and vertical components of the force applied to link CD (link 4) as a result of contact from link AD (link 1) as shown
A homogeneous rectangular flat plate that weighs WN is supported by a shaft AB and a cable C as shown in the figure. The bearing at A is a thrust bearing, and B is a radial (ball) bearing. For the loading condition shown in the figure, determine the reactions at bearings A and B. (Draw Free-Body Diagram of the system. Use a VECTORAL ANALYSIS for the solution).
- For the frame of the figure:a) Draw up the free-body diagram of the three elements that compose it, for the BCD element, set theequilibrium equations (summation of forces along the longitudinal axis "t" and the perpendicular "n", as well as thesummation of moments at point C). Note: it is not required to evaluate the reactions or the charges on the elements.b) Make a cut at the midpoint between C and D and “CALCUE” the internal loads numerically.