A transmission line has a span of 150 m between level supports. The conductor has a cross-sectional area of 2 cm². The tension in the contractor is 2000 kg. If the specific gravity of the conductor material is 9.9 gm/cm³ wind press is 1.5 kg/m length, calculate the sag.

A transmission line has a span of 150 m between level supports. The conductor has a cross-sectional area of 2 cm². The tension in the contractor is 2000 kg. If the specific gravity of the conductor material is 9.9 gm/cm³ wind press is 1.5 kg/m length, calculate the sag.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Related questions

Q: What is the minimum sized PVC Schedule 40 conduit we should use for the above wire run if it is 24…

A: 3/4"

Q: 41V (+)) - 802 W 800 V₂ + 6 402 250-2 90⁰mA 200

A: Given data Voltage source of 41 V is applied at the left periphery of the circuit. Current source of…

Q: Q3: A sinusoidally modulated AM waveform is shown below, Determine: 1. Peak amplitude of the upper…

A: Based on the bartleby guidelines solved first three subparts kindly repost the remaining questions…

Q: 2) First Order RL Circuit v1 (+21) R a) Using phasor analysis, show that the complex gain is: Ls R…

A: 2. Given Data: An RC series circuit with, Input AC voltage=V1 V Output Inductor voltage =V2 V To…

Q: Find the power of each element in the circuit shown below

Q: What is the minimum sized EMT conduit we should use for the above wire run if it is 24 inches long?…

A: a) 1/2". To determine the minimum size of EMT conduit that should be used for the given wire…

Q: The steady state current flowing through the inductor of a DC-DC buck boost converter is given in…

A: In this question we need to find the value of output capacitor.

Q: 1. Referring to the signals shown in Fig. 1: a) Find the signal energy of x(). b) Find the signal…

A: Given: Signals x(t) and y(t) as, To find: a) Signal energy of x(t). b) Signal energy of y(t). c)…

Q: The equivalent capacitance is A. B. C. D. E. 9 μµF 6 µF 3 μF 2 μF 1 μF 3 μF 6 μF

A: The given circuit diagram is shown below, The capacitance is C1=3 μF The capacitance is C2=6 μF

Q: What will be the value of R in the circuit, for sinusoidal oscillations of frequency of 2 kHz. 1kQ…

A: Given circuit- Sinusoidal oscillation of frequency of 2 kHz. To find- The value of R.

Q: Problem 4 Find V(t) for t>0 in the circuit below. Assume the switch has been open for a long time…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: List at least 3 applications of waveshaping circuits? (provide each one with explination)

A: It is asked to list at least 3 applications of wave shaping circuits. Also it is asked to explain…

Q: What is the minimum sized PVC Schedule 40 conduit we should use for the above wire run if it is…

A: 3/4". To determine the minimum size of PVC Schedule 40 conduit required for a wire run, we need…

Q: To produce a digital audio bit stream of an audio signal that contains tones at 350 Hz, 1000 Hz and…

A: Here, Given audio signal frequencies are 350 Hz, 1000 Hz and 1500 Hz. Out of these given three…

Q: What is the minimum sized IMC conduit we should use for the above wire run if it is 24 inches long?…

A: OPTION C IS CORRECT The minimum size of Intermediate Metal Conduit (IMC) required for a given wire…

Q: Problem 2 -2 x(t) Huu W 2 -2 -1 4 6 Problem 4 m 2 1 t (sec) = 0 3 Half-cycle of sine-wave 4 Consider…

Q: In an interval of 0.1 second, a coil of 100 turns whose area is 35 cm2 produces a voltage of -5.6 V.…

Q: 1.14 Suppose 8-bit digital encoding is used to represent the angle between 0° and 180° where 00h…

A: Note: The resolution of an ADC is defined as the minimum value which can be read and respond by ADC…

Q: Problem 2) Find the (a) magnetizing inductance of winding A on the stator, (b) magnetizing…

A: The given figure of the salient pole synchronous machine is shown below. We need to determine the…

Q: A discharging RC current has a resistor with R equals 40€ and T= 16s. It is known that one T equals…

A: In a discharging RC circuit, the voltage across the capacitor decreases over time and the current…

Q: Standard power rating of a 3.9 k resistor that can handle up to 100 volt drop. ㅇ 하 watt 10 watts 5…

Q: Series Inductance The supply across the terminals of this circuit is 470 V, 50 Hz. An ammeter is…

Q: Problem 2. 1V + 10 + VC 1 F HH Ic 21c 1Q 4₁ 2H 1 A t=0 S1 In the above circuit, the switch has been…

Q: A sinusoidal voltage trace displayed by an oscilloscope is shown, if the 'time/div' or Hs, switch is…

Q: For the circuit shown, R₁ = 20, R2 = 30, R3 = 20, R4 = 50, and R5 = 30. The battery voltages are…

Q: f(x) = {x 0 ). Calculate the Fourier Transform of * - 1<x<0 otherwise

Q: The current flowing through an element is (2A, 0 1 Calculate the charge entering the element from…

A: In this question We need to determine the charge Q, for interval t= 0 to t= 2s. We know Current I=…

Q: single-phase Consider an ideal full-bridge DC-AC inverter with a DC bus voltage magnitude of 1000 V.…

A: Given: An ideal full bridge single phase DC-AC inverter with, DC voltage magnitude, Vdc=1000 V. A…

Q: Considering terminals a and b: a) Use any method to solve for the Thevenin equivalent voltage. b)…

A: The thevenin's equivalent circuit can be obtained by calculating the open circuit voltage and…

Q: What are three variables that must be considered before installing a circuit breaker?

A: To explain: Three variables that must be considered before installing a circuit breaker.

Q: 1. GIVEN THE FollONING CLOSED LOOP SYSTEMS REDUCE THE BIOCK DIAGRAN TO A SINGIE TRANS FER FUNCTION

A: In this question We need to determine the transfer function of the given system. We are solving…

Q: Find the Thevenin equivalent with respect to the terminals a,b in the circuit in. Suppose that R =…

Q: From the circuit shown, I₁ at t = 0¯is Is 10A 6 A none of the given option O A 4 A 10 A R₁ 292 Six t…

Q: A constant load of 300 Mw is supplied by two 200 Mw generators, land 2, for which the respective…

Q: Derive an equation for linear signal conditioning that will convert a sensor output voltage in the…

A: Linear signal conditioning is a method of adjusting and scaling an input signal to fit the desired…

Q: A generator operating at 50 Hz delivers 1 p.u. power to an infinite bus through a transmission…

A: Given- frequency f=50 Hz, 1 p.u. power, Maximum power = 0.5 p.u. To Find- The value of δmax.

Q: Calculate the time taken by a capacitor of 1 µF and in series with a 1 MF resistance to be charged…

A: The time constant is time taken by the capacitor to charge or discharge to 37% of final value. The…

Q: How can you tell whether a given part of the system should act as a generator or a consumer? ...or…

A: Determining whether a given part of a system should act as a generator or a consumer, or as a…

Q: UL 1st digit 2nd digit Multiplier Tolerance The first band indicates: The second band indicates: The…

Q: Problem 10. Determine Vc(t) for (a) O- (b) 0+ (c) (c) ΙΚΩ 2 ΚΩ 4 ΚΩ ww 12V 1 μF VC - >6ΚΩ 2 ΚΩ ww…

Q: Consider the arrangement shown in the figure below where R = 6.50 0,= 1.40 m, and B = 2.00 T. xxxxxx…

Q: PROBLEM NUMBER 1 For the network below: a. Determine re b. Calculate Z; and Z. c. Find A.

Q: How do semiconductor diodes and transistors compare?

Q: 13.36 There is no energy stored in the circuit in Fig. P13.36 at the time the voltage source is…

A: Given:

Q: I think I need help with the algebra in here. how do you arrive at 3/4 R1 . Also it os still…

Q: Problem 3 ( - Use the properties of Boolean algebra (see Lectures 18-19) to simplify the following…

A: 'Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 2.14 The spring-mass accelerometer shown schematically in figure 2.16 has a sensing mass of 0.05 kg…

Q: Problem #4 A DSB+SC (AM) signal is given by: y(t) = (7 + 6 cos(2π800t)) cos(2π5 x 10°t) with units…

Q: Use the principle of superposition to find v, in the circuit. Take v = 23 V and i = 5.1 mA . Express…

Q: DETERMINE V₂ AND THE REQUIRED PIV RATING OF EACH DLOPE FOR THE CIRCUIT BELOW. SKETCH THE OUTPUT…

A: It is given that:

Question

Correct answer please, else downvote.

A transmission line has a span of 150 m between level supports. The conductor has a
cross-sectional area of 2 cm². The tension in the contractor is 2000 kg. If the specific
gravity of the conductor material is 9.9 gm/cm³ wind press is 1.5 kg/m length,
calculate the sag.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Single Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C and a 60-Hz resistance of 0.0956 ohm per mile at 50C for the all-aluminum Marigold conductor, which has 61 strands and whose size is 1113 kcmil. Assuming an increase in resistance of 2 for spiraling, calculate and verify the dc resistance. Then calculate the dc resistance at 50C, and determine the percentage increase due to skin effect.
A three phase, 11 KV, underground cable system, consider a single core of conductor radius 0.5 cm diameter and lead sheath of 1.25 cm. The core and lead sheath have been separated by two intersheaths with radius 0.75 cm and 1 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same.
12. There are 6 conductors in a double circuit line. Each conductor has a radius of 12 mm. The 6conductors are arranged horizontally. The center to center distance between the conductor is 2m. The sequence of conductors are from left to right as follows: a,b.c,a', b', c'. Calculate the inductance per km per phase of system. the a' 2 m 2 m 2 m 2 m 2 m
A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.
The maximum and minimum stresses in the dielectric of a single core cable are 40 KV/cm (rms) and 10 KV/cm (rms) respectively. If the conductor diameter is 2 cm, the insulation thickness is?
A three phase, 33 KV, underground cable system, consider a single core of conductor radius 0.8 cm diameter and lead sheath of 2.3 cm. The core and lead sheath have been separated by two intersheaths with radius 1.3 cm and 1.8 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same. Please i need it know please
A No.10 AWG aluminum conductor carrying a load of 16A on a 220 V, single-phase circuit. Approximate the maximum distance. Use a maximum voltage drop of 3%. (Hint: the conductor has a cross-sectional area of 10, 380 cmils) a.198.23 ft b.86.5 ft c.51.9 ft d.None of these
A 30 kV single core cable has a conductor dimeter of 2 cm and a sheath of inside diameter 6 cm. Find the maximum (peak value) and minimum stress (peak value) in the insulation.
A single core lead covered cable is to be designed for 68 kV(peak value) toearth. Its conductor diameter is 2 cm and its three insulating materials havepermittivities of 5, 4 and 3 respectively with the corresponding maximumsafe working stress of 38 kV/cm (r.m.s), 26 kV/cm (r.m.s) and 20 kV/cm(r.m.s) respectively. Find the minimum diameter of lead sheath.
Assume that a single-conductor belted cable has a conductor diameterof 0.681 in., inside diameter of sheath of 1.7025 in., and a length of8000 ft. The cable is to be operated at 12.47 kV. The dielectricconstant is 4.5, and the power factor of the dielectric at a ratedfrequency and temperature is 0.05. Calculate the following:(a) Capacitance of cable.(b) Charging current.(c) Dielectric loss of cable.(d) Equivalent resistance of insulation.
Problem #1 • An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.
The Cost OF Single phase overhead feeder is OMR q Per KM(a is area of cross section in sq mm) and the intrest and depre Ciation Chargs onfeeder omical carrent density are 7Y. defermain to use for the most econor requiring Full load current of 27% of the 12 baisa is year. The Cost per unit ass ume resistance of Im lenahth length and I mm² secfion of Conductor as 1/32 find Current densi ty =?