A torque T = 3 kN • m is applied to the solid bronze cylinder shown. Determine (a) the maximum shearing stress, (b) the shear- ing stress at point D, which lies on a 15-mm-radius circle drawn on the end of the cylinder, (e) the percent of the torque carried by the portion of the cylinder within the 15-mm radius. 60 mm 30 mm- T=3 kN - m- 200 min

A torque T = 3 kN • m is applied to the solid bronze cylinder shown. Determine (a) the maximum shearing stress, (b) the shear- ing stress at point D, which lies on a 15-mm-radius circle drawn on the end of the cylinder, (e) the percent of the torque carried by the portion of the cylinder within the 15-mm radius. 60 mm 30 mm- T=3 kN - m- 200 min

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 60 mm- В 90 mm- 100 mm C 4 kN 80 mm D 140 mm
1. The axle of the car is subjected to forces and moment shown, where the diameter of the axle is given as 32 mm (and specific distances are 0.15 m and 0.2 m, respectively). At Point A, i. Calculate the principal stresses. ii. iii. Calculate the maximum shearing stress. Draw Mohr's circle with associated values shown. 350 N·m 3KN 3kN A
Q2) The aluminum rod BC (G-26 GPa) is bonded to the brass rod AB (G-39 GPa). Knowing that cach rod is solid and has a diameter of 12 mm, Hrass 300 Ahamin determine the angle of twist (a) at B, (b) at C. Then find the maximum stress in the Brass and Aluminum bars. 100 N
200 mm Q2) The aluminum rod BC (G-26 GPa) is bonded to the brass rod AB (G-39 GPa). Knowing that irass cach rod is solid and has a diameter of 12 mm, 300 Alamuinm determine the angle of twist (a) at B, (b) at C. Then find the maximum stress in the Brass and Aluminum bars. 100 N
A 7/8-in.-diameter steel rod AB fitted to a round hole near end C of the wooden member CD. A shearing stress of 145 psi acts on the surfaces indicated by the dashed lines. a. Determine the maximum normal stress (in psi) in the wood. b. Determine the distance b (in inches) for which the shearing stress is applied. Round off to a whole number. c. Determine the bearing stress (in psi) between the steel rod and the wood.
Three forces are applied to the machine component ABD as shown. Knowing that the cross section containing point His a 20 x 40-mm rectangle, determine the principal stresses and the maximum shearing stress at point H. Take force Q=2.9 kN. (Round the final answers to two decimal places.) y 50 mm 2.5 kN 20 mm MPa MPa 150 mm 40 mm 0.5 KN 160 mm The principal stresses at point Hare as follows: da ab= The maximum shearing stress at point His( MPa.
A pressure vessel of 225-mm inner diameter and 6-mm wall thickness is fabricated from a 1.2 m section of spirally welded pipe AB and is equipped with two rigid end plates. The gage pressure inside the vessel is 2 MPa, and 45-kN centric axial forces P and P' are applied to the end plates. P' A 1.2 m 35⁰ B Determine the shearing stress parallel to the weld. The shearing stress parallel to the weld is P MPa.
2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable axial stress of the puncher is limited to 101.85 MPa, determine the thickness (t) of the steel plate. The maximum shear stress of the steel plate is 50MPa.
The compressed-air tank AB has a 250-mm outside diameter and an 8-mm wall thickness. It is fitted with a collar by which a 40-kN force P is applied at B in the horizontal direction. Knowing that the gage pressure inside the tank is 5 MPa, determine the maximum normal stress and the maximum shearing stress at point K. (Round the final answers to one decimal place.)
QUESTION 1. Determine the constant thickness t of the square shaped tube if the average shear stress is not to exceed 90 MPa when a torque of T- 3 kN m is applied to the tube. Neglect the stress concentrations at the comers. T-3 kNm 200 m 200 mim
Re Several forces are applied to the pipe assembly shown. Knowing that Q= 250 lb and that the pipe has inner and outer diameters equal to 1.61 in. and 1.90 in., respectively, determine the normal and shearing stresses at point Hand point K. (Round the final answers to two decimal places.) 150 lb 10 in. 4 in. 150 lb 6 in. 50 lb 4.79 O ksi. The normal stress at point His The shearing stress at point H is 83.63 -41 ksi. ksi, The normal stress at point K is 3.83 O ksi. The shearing stress at point K is
Q 3: -Knowing that the bracket AB has a uniform thickness of in., determine (a) the principal planes and principal stresses at point H. (b) the maximum shearing stress at point H. 3 kips 30° 51 5 in. 0.75 in. K. H® 1.25 in.) B 2.5 in.