A three-phase, 480 V, six-pole, Y-connected, 60 Hz, 10 kW induction motor is driving a constant torque load of 60 Nm. The parameters of the motor are: R₁ = 0.4 02, R₂ = 0.50 (actual rotor resistance), Xeq = 40, N₁ / N₂ = 2 (turn ratio between stator and rotor windings) Calculate the following: a. Motor torque. b. Motor current c. Starting torque d. Starting current A voltage is injected in the rotor circuit to reduce the motor speed by 40%. e. Calculate the magnitude of the injected voltage. f. Repeat (a) to (d) for the motor with injected voltage. g. Calculate the power delivered to the source of injected voltage.

A three-phase, 480 V, six-pole, Y-connected, 60 Hz, 10 kW induction motor is driving a constant torque load of 60 Nm. The parameters of the motor are: R₁ = 0.4 02, R₂ = 0.50 (actual rotor resistance), Xeq = 40, N₁ / N₂ = 2 (turn ratio between stator and rotor windings) Calculate the following: a. Motor torque. b. Motor current c. Starting torque d. Starting current A voltage is injected in the rotor circuit to reduce the motor speed by 40%. e. Calculate the magnitude of the injected voltage. f. Repeat (a) to (d) for the motor with injected voltage. g. Calculate the power delivered to the source of injected voltage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2. A 230 V single-phase induction motor, 50 Hz, has the following winding impedances (at rest): Zm=28 <70° Q. Za=42 <45°Q A) Calculate the input current at start-up. B) Obtain the amount of capacitor in series with the auxiliary winding for which the torque Maximum startup. Then compare the input current, auxiliary winding current and torque all at start-up in two modes with and without starter capacitor.
A large 3-phase, 4160 V, 60 Hz, squirrel-cage induction motor draws a current of 400 A and the total active power of 2500 kW when operating at full-load. The corresponding speed is accurately measured and is found to be 1178 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.15 0. The total iron losses are 26.5 kW and the windage and friction losses are 15 kW. Calculate the following: The power factor at full-load The active power supplied to the rotor The total I²R losses in the rotor The load mechanical power [kW], torque [kN.m], and efficiency [%] a. b. C. d.
I need the full and correct expert solution for handwriting
A three-phase induction motor used for a commercial application in Oman 50HZ runs at 584 rpm at no load and at 546 rpm at full load. a) How many poles do this motor have? b) What is the percentage slip at full load? c) The frequency of the rotor currents when slip is 7 % d) The frequency of the rotor currents at standstill.
2) A large 3-phase, 4000 Va (phase to phase), 60 Hz squirrel-cage induction motor draws a current of 385 A/phase. The total active power at the stator input terminals is 2344 kW, when operating at full load. The corresponding speed is accurately measured and found to be 709.2 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.10 Q. The total iron losses are 23.4 kW and the windage and friction losses are 12 kW. Calculate the following: c) The total 1²-R losses in the rotor d) The load mechanical power (kW), torque (kN•m), and efficiency. S = Va · V3 - I S= Vy•3·I %3D
Hury up pleaaaaaaase
A three-phase, two-pole, 35 hp, 480 V, 60 Hz, Y-connected induction motor has the following constants in ohms per phase referred to the stator: R = 0.322N R2 = 0.196 Q X1 = 0.6752 X2 = 0.510Q Xm = 12.52 The total rotational losses are 1850 W and are assumed to be constant. The core loss is lumped in with the rotational losses. For a rotor slip of 3% at the rated voltage and rated frequency, determine the following: (a) The speed in rpm and in rad/s power factor (d) The developed power and output power (e) The developed torque and output torque (f) The efficiency. (b) The stator current (c) The
In a 3-phase, 4-pole induction motor, The power crossing the air gap of a 60 Hz is 42.6 kW, and the power converted from electrical to mechanical form in the motor is 39.6 kW. If the total mechanical losses are 1000 W, find the load torque of this motor? Select one: O a. None O b. Tload = 208.4 N.m. O c. Tjoad = 232.6 N.m. O d. Tjoad = 220.3 N.m. Clear my choice
3. A 440V 60-hp six pole 60 hz A connected induction motor has the following parameters R1=0.048 R2= 0.035 Xm= 9.50 X1= 0.33 0 X2= 0.37 0 Pcore= 600W PF&W= 350W Use the Thevenin's Equivalent circuit concept to find: (a)Vth and Zth seen by the rotor circuit (b)The slip at which maximum torque occurs (c) the value of Max/pullout Torques (d) The starting torque.
A synchronous machine is a three-phase, two-pole machine with 36 stator slots and 5/6 full-pitched balanced armature windings. Each phase winding is made up of eight identical coils connected in sequence. Balanced three-phase 66 Hz currents with a peak amplitude of 16 A are used to drive the stator phases. a) What is the basic stator space mmf's maximum amplitude? (A.turns) b) How fast does the fundamental stator space mmf rotate mechanically? (rpm) c) What is the third-harmonic stator space mmf's maximum amplitude? (A.turns) d) What is the fifth-harmonic stator space mmf's maximum amplitude? (A.turns) e) How fast does the fifth-harmonic stator space mmf rotate mechanically? (rpm)
B3. A three-phase, 60 Hz 4-pole induction motor has a slip of 0.05 when the output is 30 kW. The frictional loss at shaft is 300 W. Calculate the following: (i) the rotor speed in r.p.m. (ii) the torque delivered by the rotor. (iii) the torque delivered to the rotor. (iv) the rotor IR loss.
S1) please hury up its late