S4) just Solve A A) The circuit of the thermocouple made of iron and Constantan is shown in Figure 4.If the base connection is inside the ice container 0 °C and the output voltage of the thermocouple is2.1mV, obtain the connection point temperature.B) If in the thermocouple circuit discussed in section A (shown in Figure 5), ice is melted in thecontainer in which the base connection is located, so that it turns into water with a temperature of25°C and the connection related to the temperature measurement in Remained the sametemperature, what is the output voltage of the thermocouple?IronPotentiometerConstantanIronMeasuringjunctionIce bathReferencejunctionFigure 4 Circuits for a thermocouple made of iron and Constantan.C) If copper branches are added to the thermocouple circuit according to the figure below. In the casewhere the connection of the base inside the ice 0°CAnd the output voltage is 2.1 mv, calculate the temperature of the measuring connection.IronCopperConstantanCopperPotentiometerMeasuringjunctionIce bath-ReferencejunctionFigure 5: Thermocouple circuit made of iron, Constantan and copper.The thermoelectric sensitivities for constantane, copper and iron in contact with platinumat 0°C are-35", +6" and +18.5 respectively.

Answered: Image /qna-images/answer/c2e10866-6ece-49ba-bd35-396cb00ed555.jpg

A) The circuit of the thermocouple made of iron and Constantan is shown in Figure 4. If the base connection is inside the ice container 0 °C and the output voltage of the thermocouple is 2.1mV, obtain the connection point temperature. B) If in the thermocouple circuit discussed in section A (shown in Figure 5), ice is melted in the container in which the base connection is located, so that it turns into water with a temperature of 25°C and the connection related to the temperature measurement in Remained the same temperature, what is the output voltage of the thermocouple? Iron Constantan Iron Potentiometer Measuring junction

A) The circuit of the thermocouple made of iron and Constantan is shown in Figure 4. If the base connection is inside the ice container 0 °C and the output voltage of the thermocouple is 2.1mV, obtain the connection point temperature. B) If in the thermocouple circuit discussed in section A (shown in Figure 5), ice is melted in the container in which the base connection is located, so that it turns into water with a temperature of 25°C and the connection related to the temperature measurement in Remained the same temperature, what is the output voltage of the thermocouple? Iron Constantan Iron Potentiometer Measuring junction

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw circuit diagram of 4×4 multiplier.
4:45 M 3 all all 18% Question 1 Design the following 4 to 2 Priority Encoders 1) DO> D1 > D2 > D3 2) D2> DO > D3 > D1 3) D1> D3 > D0 > D2 4) D3 > D2 >D1 > D0 II
What are don’t care conditions for the function F=A´B´C´D+A´BC+AB´C if its simplification gives us F=A´C+B´C+A´B´? a)d=A´B´+A´D b)d=A´C´+A´D c)d=A´B´C+A´D d)d=A´B´C+A´B´D´ e)d=A´B´C+A´BD´
The simplification of the following by using a 4-variable k-map AD' + B'C'D + BCD' + BC'D' gives: F = AD' + C'D + BCD' True False
Please, solve this MCQ
Design a four-bit variable resistor network DAC using R1=1 K ohm and RL=1000 K ohm resistors for (0 = 0V and 1 = 15V). Then write down the table that has all conversions from (0000 to 1111).
al C2 C3 C1 C4 Find Ceg at the (a,b) terminals given that C-4.6 IF C2-7.3 uF C3-3.6 UF CA-6.3 uF Note: Your answer should be round to the nearest single digit decimal place. Your answer will be in micorFarads. For example, if you compute 1.63x10-° then enter 1.6 as your answer. 52 F P Type here to search delete iome backspace lock 9.
4.47.3 In the circuit shown in the image below, if R1 = 38 Q, R2 = 37 Q, and 1 A, determine the Norton current IN (in A) for its Norton equivalent circuit observed = 1.9 between terminals a and b. R2 R1 +. 20lv Please pay attention: the numbers may change since they are randomized. Your answer should keep 1 place after the decimal point. Your Answer: Answer
D4
REDUCE THE BLOCK DIAGRAM USING MANUAL ALGEBRA, DON'T USE THE RULES., THANKS.
14. If "a" is 0.05, v2 and v1 are 6 and 8 respectively; Accordingly F critical value is: Select one: a. 4.15 b. 4.51 c. 3.85 d. 3.58