A) The Boolean representation of this PLC program is: B B C E * HHI B B) Identify the problem in this motor control PLC program: Start switch Stop switch Motor run Motor run # A=BCD + A_ Coil O A=BCD + B_ Start contact A=A+ (B C E) _ Stop contact O A=BCD + BDF_Power source O A=BCD + BCE + BCF_Seal-in contact

A) The Boolean representation of this PLC program is: B B C E * HHI B B) Identify the problem in this motor control PLC program: Start switch Stop switch Motor run Motor run # A=BCD + A_ Coil O A=BCD + B_ Start contact A=A+ (B C E) _ Stop contact O A=BCD + BDF_Power source O A=BCD + BCE + BCF_Seal-in contact

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 1SQ: Describe what is meant by sequence control.

See similar textbooks

Similar questions

please i need help quickly n 57 The ARDUINO IDE stands for. d a. Integrated development environment out of b. None of these O c. Integrated drive electronics O d. Instructional development environment 58 What does the following ARDUINO command do? analogWrite (9, 63) a. Sets the PWM duty cycle to 25% ut of b. Sets the PWM duty cycle to 75% c. Sets the PWM duty cycle to 50% d. Sets the PWM duty cycle to 30%
A 1-p On-Off AC voltage controller supply voltages of 440 volts and the output obtained is 220 volts. The number of Off cycles is 75. Find the number of On cycles. 50 25 O 100 O 75
List the pins on Arduino that can do analog write. In a PWM, given that the duty cycle is 80% what is the voltage output? In a PWM, what should be the duty cycle to get a voltage output of 4.5 V? Given the bellow Arduino command: analogWrite( 8, 200); What is the duty cycle? What is the voltage output?
By using modular PLC type LG write the PLC LIP that generates a square wave of 4 Hz and 70 % duty cycle. Use NO start Button and NC stop Button and a led as indicator.
(c ) The most common analogue signals for PLC appear in the form of a 4-20mA current signal. Explain the reason for using current signal of 4-20 mA form. (d)Explain the operation of the ladder diagram as shown in Figure 5. Start, PB Stop PB Coil I:13/05 0:12/03 I:13/04 Coil O:12/03 Figure 5
Required information A fan is to run only when all of the following conditions are met: • Input A is OFF. • Input B is ON or input C is ON, or both B and Care ON. • Inputs D and E are both ON. . One or more of inputs F, G, or H are ON. Saved Note: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Identify the correct typical PLC ladder logic diagram for the given control system. Multiple Choice
ASYNCIN Dan Synchronous System CLOCK Figure Q4 (b) The circuit in Figure Q4 (c) consists of edge triggered flipflops. The second flipflop receives the clock signal through a long slow path which results in delay. Answer the following questions: Q1 Q2 IN DaK CLOCKD CLK CLOCK A long, slow path Figure Q4 (c) 林 Define clock skew, Explain with a timing diagram, what problem this circuit might face? What condition it must satisfy to ensure that the intended circuit output is not affected? For the following LFSR circuit in the Figure Q4 (d), let the initial entries of stages R, be S, for 0sisn. Compute the first 12 bit output for the following cases of initial entries: (d) S2 Si So Case 1 Study Pack Practice &A Case 2
A step up chopper has an input of 200 volts and output of 250 volts. The blocking period is each cycle is 0.6x10-3 seconds. Find the period of conduction in each cycle and frequency of operation?
Describe what is meant by sequence control.
Describe DCS and PLC control systems.
What is the meaning of “ON DELAY” in Time relay RXKL at AC-operation . (Explain Briefly)
Discuss about Power Thyristor's DC and Ac switching.(with Diagram)