A tank contains two substance oil (A) and water (B) subject to variable air pressure; the dimension is shown below and corresponds to 1atm. If air is slowly added from a pump to bring pressure p up to 1MPA gage, what will be the total downward movement of the free surface of oil and air? Take average values of bulk moduli of elasticity of the liquids as 2050MPA for oil and 2075MPA for water. Assume the container does not change volume. Neglect hydrostatic pressures. Air DE 200 mm 600mm Oil Water 700 mm 300 mm

A tank contains two substance oil (A) and water (B) subject to variable air pressure; the dimension is shown below and corresponds to 1atm. If air is slowly added from a pump to bring pressure p up to 1MPA gage, what will be the total downward movement of the free surface of oil and air? Take average values of bulk moduli of elasticity of the liquids as 2050MPA for oil and 2075MPA for water. Assume the container does not change volume. Neglect hydrostatic pressures. Air DE 200 mm 600mm Oil Water 700 mm 300 mm

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.13P: 5.13 The torque due to the frictional resistance of the oil film between a rotating shaft and its...

See similar textbooks

Similar questions

Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen, air, and saturated steam at a temperature of 100C. Let D=1m,U=1m/sec, and hc=1W/m2K.
The figure belows shows a closed tank holding air and oil to which is connected a U-tube mercury manometer and a pressure gage, with L1 = 3 ft, L2 = 0.5 ft, and L3 = 1.75 ft. The densities of the oil and mercury are 55 and 845, respectively, each in Ib/ft?. Let g = 32.2 ft/s?. Pressure gage Air Oil (p = 55 Ivit) Pam Mercury (p= 845 Ih/n') g= 322 fus? Determine the reading of the pressure gage, in Ibf/in.? (gage). Pgage = i Ibf/in.2
(5) Pressure Cooker (6) Carburetor (7) Radiator of an automobile. 2. Convert the following reading of pressure to kPa, assuming that the barometer reads 760mm Hg. (1) 90cm Hg gauge (2) 40cm Hg vacuum (3) 1.2m H20 gauge 3. Five masses in a region where the acceleration due to gravity is 30, 5 ft/s are as follows: m, is-
A U-tube manometer indicates a pressure drop of 10 in. water across in an air filter. The air is at 26 C and a pressure of 60 lbf/in2 : (a) What is the pressure drop in lbf/in2 and in atm? (b) What percentage of error is introduced if the density of the air in the manometer leads is neglected. (Air density = 1.168 kg/m3 ) (g =32.17 ft/s2)
In Figure below all fluids are at 20 deg.C. Determine pressure at point B, if pressure at point A is 150 kPa and weight of air is neglected. Use the table below for the densities at 20 deg.C. Liquid p. kg/m Kerosene - Ammonia 608 Benzene 881 Air Carbon tetrachloride 1590 Benzene Ethanol 789 Ethylene glycol Freon 12 B 1117 40 cm 9 cm 1327 20 cm Gasoline 680 14 cm Glycerin Kerosene 1260 t8 cm 804 Mercury- Water Mercury Methanol 13,550 791 SAE 10W oil 870 SAE 10W30 oil 876 SAE 30W oil 891 SAE 50W oil 902 Water 998 Seawater (30%e) 1025
Select the correct value of H: ( The density of liquid =990 kgim, gravity g = 9.81 mis and L= 90 cm, Pressure P1= 52.369 Kpa) Air Pt Liquid (2)
Balloons are used for touristic travel in certain regions.For this travel, aforce is required to push the balloon upward.The force is expressed as below; ?balloon=pair x g x vballoon.Assume that the balloon has a 500-cm-diameter, the density of air is 1,23x10−3g/cm3. A-definedgas is used to fill the balloons and itsweight is approximately 1:7 of the weight of air.Neglect the other weights. The balloon carries three people. The people’s weights are67, 75 and 83 kg, respectively.Determine the balloon’s acceleration when it is first released.
Answer all the questions 1) Using dimensional equations, convert: 700 m* /(day. kg) to cem* /(min. g). 2) Convert 210 X 10 kJ/min to hp 3) Calculate the weight in lbr of a 30.0-lbm object. 4) Calculate the mass in kg of an object that weighs 25 Newton. 5) The density of a fluid is given by the empirical equation: p = 70.5 exp(8.27 x 10-7P) where p is density (Ib/ft) and Pis pressure (lb,/in.?). (a) What are the units of 70.5 and 8.27 x 10-7? (b) Calculate the density in g/cm for a pressure of 9.00 x 10 N/m?. 6) The vapor pressures of 1-chlorotetradecane at several temperatures are tabulated here. T(C) 98.5 131.8 148.2 166.2 199.8 215.5 p* (mm Hg) 1 5 10 20 100 60 Use two different method to estimate the value of P' at T = 190 °C (7) The specific gravity of gasoline is approximately 0.70. a- Determine the mass (kg) of 50.0 liters of gasoline. b- The mass flow rate of gasoline exiting a refinery tank is 1150 kg/min. Estimate the volumetric flowrate in liters/s.
An oil drum of 500 mm diameter and 1.5 long is to be rolled across a footstep of 100 mm high. Find the minimum push required at the top of the drum. Take density of the oil as 1 kg/litre. Neglect weight of the drum. [Ans. 1444.5 N]
Q5: The compart ments (B) 4 CC) in figure below are closed & filled with air. When the gauges (A) (D) read as indicated, when should be the value of Cx) for gaugeCE)? (Mercury in each U-tube gauge) 2.07 bar C B. 254 Air Air E.
1. The deformation of the fluid will continue as long as the 2. When designing gates, vessels, dams or other bodies that are submerged in a liquid, it is important not only to estimate the - 3. The surface tension is the tensile force per -- in any direction along the surface the surface tension. 4. The value of - specifies whether the fluid can be assumed compressible or incompressible. 5. Archimedes' principle indicates- 6. A truck is filled with gasoline. If the container (tank) on the truck undergoes a - - is applied. - but also to specify its location on the body. then the liquid surface will begin to rotate clockwise about the center of the container and will eventually maintain a fixed tilted position.
A special tyre was inflated at 2 bar gage pressure on Earth, where the atmospheric pressurewas 1013 hPa and the acceleration of gravity 9.81 m/s2.The tyre was then transported without pressure leakage on Mars, where the atmosphericpressure was 6 mbar and the acceleration of gravity 3.7 m/s 2.Questions:(a) Measuring on Earth the tyre pressure with a mercury manometer, what was themanometer reading in mm?(b) Measuring on Mars the tyre pressure with a mercury manometer, what was themanometer reading in mm?