A tank contains gasoline sp. gr. = 0.90, oil sp. gr. = 0.8, and seawater sp. gr. = 1.03. If the depths of the liquids are 0.5 m. for oil, 0.6 m. gasoline, 1 m seawater. respectively. Find the pressure IN kPa at a depth of 1.4 m. Use 3 decimal places.

A tank contains gasoline sp. gr. = 0.90, oil sp. gr. = 0.8, and seawater sp. gr. = 1.03. If the depths of the liquids are 0.5 m. for oil, 0.6 m. gasoline, 1 m seawater. respectively. Find the pressure IN kPa at a depth of 1.4 m. Use 3 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: ion 1: The absolute pressure in a gas tank is 300 kPa. Determine the gage pressure

A: Given data : The value of absolute pressure=PAbs PAbs=300 KPa The value of atmospheric pressure…

Q: Q4. The tank is filled with aqueous ammonia (ammonium hydroxide) to a depth of 3 ft. The remaining…

Q: What is the pressure 1.5 m below the liquid surface?

Q: Determine the height of the water from the right leg if the liquid added in the left leg has a…

A: Using pressure equation:P+ρlghliq=ρwghw

Q: An oil of viscosity 9 poise is flowing through a horizontal pipe of 60 mm diameter. If the flow is…

A: Laminar flow- Diameter of pipe=D = 60 mm Viscosity of oil μ= 9 poise = 0.9 N-s/m2 Pressure drop =…

Q: . For the tank shown in figure below, determine the depth of the oil h if the reading of the bottom…

Q: d. Situation XXI. A 20 cm diameter pipe length of 100 m with z = 60 m, f 0.02 m and loss of head due…

A: Solution:- Given details: Diameter of pipe, d =20 cm, Length L =100 m. Head loss coefficient k =0.5…

Q: (4) Consider that we have a horizentral pipe, like shown in the sketh, which is carrying in this…

A: Elevation of tank (z1) = 100 mElevation of pipe (z2) = 20 mDiameter of pipe (D) = 20 cm = 0.20…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

Q: 2. Determine the height of the water from the right leg if the liquid added in the left leg has a…

Q: A pressure gage at elevation of 12m at the side of the tank containing liquid reads 100 kPa. Another…

Q: Oil (SG oil = 0.95) flows at 200 L/s through a 200mm diameter pipe, 500m long. Friction factor is…

A: Given data SG of oil = (Go) = 0.95 Friction factor (f) = 0.0225 Length of pipe (L) = 500 m…

Q: 3. Oil is flowing in a pipe under the condition shown. If the total head loss from point 1 to 2 is 3…

A: Head loss : The amount of head, pressure, or energy lost by water passing through a pipe or channel…

Q: Determine the elevation at point A (ha) if the air pressure in the sealed left tank is -32 kPa. All…

Q: An incompressible fluid flows through a horizontal pipe which tapers from a diameter of 2 cm to a…

Q: A 0.1m-Φ x 0.094m solid cylinder weighs 4 Newton. It is submerged in a liquid (SG = 0.8328) which is…

Q: Oil (SG = 0.83) flows at a rate of 200 L/s through a 500m pipe with a diameter of 200mm. The…

Q: The gage pressure in a liquid at a depth of 2.5 m is read to be 26 kPa. Determine the gage pressure…

A: Given Data Gauge pressure at depth of 2.5m (P2.5) = 26 kPa Determihe the gauge pressure in the same…

Q: Compute for the unknown pressure at A. = 90 cm; h2 = 150 cm; h3 = h4 =65 cm). Encode your answer…

Q: uid mechan

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: figure below at 100 m3/hour. What should be the elevation ( in meters) in the upper reservoir? The…

Q: In a uniform diameter smooth pipe measuring 30 cm, a pressure of 60 kPa was measured at section 1,…

Q: 88.18 liters of a distinct liquid weig ermine its density ( D0 liter = 1 m3

A: Given data- Mass(m) = 417.91kg Volume(V)= 388.18 lit 1 m³ = 1000 lit Volume(V)= 388.18 lit =…

Q: AIR 41cm 4m

Q: -8.33 -0.12 8.33 (1) 0.12 -L Darcy Experiment A set-up of Darcy Experiment involves measuring the…

A: Given data Hydraulic head at section-1 (h1) = 66cm Hydraulic head at section-2 (h2) = 54cm Length…

Q: Given a three-pipe system, the total 150,000 Pa, and the elevation drop data are:

Q: Oil (sg-0.87) flows from A to E as shown. The head loss is assumed to be as follows: A to B = 0.45…

A: Given, Pipe diameter BD = 18 in Pipe diameter DE = 8 in

Q: Determine the difference in pressure (kPa) between A and B. a= 4.06 meters b= 2.96 meters

Concept explainers

Pressure and Stress

Question

A tank contains gasoline sp. gr. = 0.90, oil sp. gr. = 0.8, and seawater sp.
gr. = 1.03. If the depths of the liquids are 0.5 m. for oil, 0.6 m. gasoline, 1 m
seawater. respectively. Find the pressure IN kPa at a depth of 1.4 m. Use 3
decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data.

VIEW

Step 2: Obtaining the total pressure in KPa at depth 1.4 m from surface.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A smooth pipe with a constant diameter 0.20 m carries water at a temperature of 30oC (Refer Table Q4(c)). The Pipe pressure at section 1 and section 2 is 50 kPa and 20 kPa, respectively. Section 1 is located 2 m lower than section 1. Determine the head loss in the pipe.
An oil of viscosity 8 poise flows between two parallel fixed plates which are kept at 60 mm distance. The pressure drop over the length of 150 cm is observed to be 4.5 kPa. The width of the plates is 0.2 m. The discharge of flow (in Ips) is [Assume laminar flow.]
The gage pressure (psig) at point a is nearest (a) 13.7 (b) 14.7 (c) 101.3 (d) 0 (e) 1 Oil a 3 in SG = 0.69 SThe gage pressure (psig) at point c is nearest (a) 57.2 (b) 1.4 (c) 6.7 (d) 0.4 8 in Water The absolute pressure (psia) the natural gas pipeline is nearest h, = 22 in (a) 8.4 (b) 65 (c) 9 (e) 23 16 in SThe gage pressure osig) in the natural gas pipeline is Natural gas Dif the pipeline pressure was increased by 50%, what cost- effective manometer modification(s) might be needed? (b) More mercury, less oil (c) Add 2 more manometer loops (d) Replace the manometer with a high-pressure gage (e) Rotate the gas line to a vertical alignment Mercury SG = 13.6
A cylinder is placed in a steady water flow as shown. Calculate the pressure difference PB - PA in psi if the flow speed at A is 10 ft/sec. .A O 1.04 O 1.53 0.67 1.92 0.82 O 1.74
3. What is the pressure difference between pipe A and pipe B? Give pressure difference in kPa. (y = 1.22 m and h 30 in.) The gage fluid, M, is mercury with a specific gravity of 13.54 State assumed values if any. Water A Water B y D Liquid M
Consider the tank shown in (Eigure 1). Take po = 900 kg/m³, Pu=1000 kg/m³, and pHg = 13 550 kg/m³. 0.6 m 0.8 m 100 mm h 1 of 1 > P Part A Determine the level of water in the tube if the depths of ol and water in the tank are 0.6 m and 0.8 m. respectively, and the height of mercury in the tube is h=0.075 m A Express your answer to three significant figures and include the appropriate units. PA h = 240 Submit + Provide Feedback → OF ? mm Previous Answers Request Answen X Incorrect; Try Again; 4 attempts remaining Next > 1231 AM 0
Assignment-1: Water fills the vessels shown in the figure below. Specific gravity of manometric liquid is 0.9: (a). Find the difference in pressure intensity at m and n when h = 1.25 m and z = 0.3 m; (b). Instead of water mercury in the vessel and manometric liquid has specific gravity of 1.6; find in the pressure intensity at m and n if h = 0.6 m and z = 1.0 m. ARARA POR nannnnnng
03. Find the pressure difference between A and В Oil RD = 0.8 Water 0.4m 0.2m 0.3m Water 0.4m 0.4m B (a) 1692 Pa (b) 1913 Pa (c) 2141 Pa (d) 2551 Pa
Q3. SAE 30 oil (Sp. Gr. =0.833) with a dynamic viscosity 0.28 N.S/m? flows in a 4-cm-diameter pipe which is inclined with an angle 37°. For the pressure measurement shown, determine A. Whether the flow is up or down The flow rate in m'/h C. The shear stress and velocity 1 cm from the boundary Draw the shear stress and velocity profile with the section of the pipe. В. D. P-180 kPa P- sOokPa 15m 20m
A 25-mm-diameter pipe 35m long is used to convey oil. The oil has a density of 880kg/m³ and a kinematic viscosity of 0.25×10*m³/s. The discharge in the pipe is Q=24x10*m³/min. Given that the pipe is placed horizontally and there are no any minor losses. Determine the pressure drop between the entrance and exit of pipe.