A tacheometer was placed at point P toestimate the horizontal distances PQand PR. The corresponding stadiaintercepts with the telescope kepthorizontal, are 0.320 m and 0.210 m,respectively. The ZQPR is measuredto be 61° 30' 30". If the stadiamultiplication constant =100 and the%3Dstadia addition constant =0.10 m. Thehorizontal distance (in m) between thepoints Q and R is[2 Marks]PR.

Answered: Image /qna-images/answer/9b6f51b4-b2d1-43f0-99fe-f8ae9a3ff029.jpg

Answered: A tacheometer was placed at point P to…

Engineering

Civil Engineering

A tacheometer was placed at point P to estimate the horizontal distances PO

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A student was asked to layout a 500 m long line using a 25 m tape that is of standard length at a…

Q: Determine Ix of the shaded area shown in the figure below

A: Consider the figure,

Q: Q- Calculate the corrected staff reading at point A, if the staff reading is taken from an…

A: Given data: Distance, d = 1.5 km Staff reading from instrument= 3.46

Q: Station A B C Angles 41° 73° 67° No. of Measurement 4 6 2 A. Compute the most probable value of…

A: Weight is inversely proportional to number of observation

Q: Distance BD = 12.8 m Distance ED = 7 m Know that the line CB is parallel to the line ED. The width…

Q: An upright aerial photograph is taken using a camera focal length of 150.7 mm, where there are 2…

Q: 1) 2 points B &C were observed from point A where the instrument was set up at a height of 1.25m.…

Q: 21: The figure below represe riangle (abc), Azimuth b to d where ab-bc= 50m. d = dc= 40m. calculate…

A: GIVEN,FB of bd = 110°ab = bc = 50 mand ad = dc = 40 m to determine length of bd angle a,b, and c…

Q: Solve the following using Double Integration Method lo kaN /ma いニ Aon =? man bm ル EI = lo00 kN-m2

A: given- simply supported beam with UDL to find - maximum deflection.

Q: With your pencil, make a dot on the position of your best visual estimate of the centroid of the…

Q: Azimuths are horizontal angles observed clockwise from any reference meridian. True False

A: Azimuths are horizontal angles measured in clockwise direction from any reference meridian.…

Q: LINE AZIMUTH FROM NORTH AB ВС CD DE EF

Q: show complete solution) 2. A stadia rod held at a distant point B is sighted by an instrument set…

A: Given Lower value =0.5 Upper value =1.6

Q: Define Normalized CPT Parameters

A: Cone penetration testing (CPT) is used to identify the soil type. In this test a cone penetrometer…

Q: Trapezoidal formula is also known as 7 O Average end area method O Simpson's rule O Double-meridian…

Q: 2. An engineer's level with stadia constant of 0.3 and stadia interval factor of 100 was set up at…

A: stadia constant =c =0.3 stadia interval factor= 100

Q: What is the angle reading in the vernier?

A: The angle readings in the vernier for the given figures have to be determined.

Q: 4. There is a fort on a hill in Jaipur. Adjacent to the hill, Delhi-Jaipur NH8 is passing through.…

A: Tachometer constant k = 100 and C = 0 (Given)

Q: what is the meaning of the friction angle

A: The angle of a plane to the horizontal when a body placed on the plane will just start to slide is…

Q: Activity 1. From the rectangular area shown a semi-circle of radius 4 cm is removed. Locate the…

Q: 1. The distance from points A to point B was recorded as 576.35 m and the reverse distance was…

A: Given data, Distance from A to B = 576.35 m Reverse distance from B to A = 576.39 m

Q: A 50-m tape was used to measure distance AB as 945.60m. The tape was discovered to be 50.075m after…

A: Given data, Designated tape length l = 50 m Actual tape length la = 50.075 m Length to be measured L…

Q: 1. What is the distance between the stadia hairs on the instrument's scope? (answer in mm) 2. What…

Q: A lot is in the form of a regular Hexagon. If the magnetic deflection when they measured side EF is…

Q: 300kn 15° W 50°

Q: Distance by Tachymetry 1. A stadia rod held at a distant point E is sighted by an instrument…

Q: Determine the horizontal distance from A to B if the readings are: ROD STADIA READING POSITION UPPER…

Q: Question 1 Listen For 0° < 0 < 360° ,find the angles that satisfy the equation cos(0) = 0.2857 Round…

A: ● solution:- b) As we can see that the values are given like:- cos @ = 0.2857 And @ value should…

Q: Calculate the vertical distance between X and Y. When a tacheometer is set up at X and the readings…

A: Given- Readings on staff at Y are 1.77 m, 2.12 m & 2.34 m, Inclination of line of sight = +1o 9'…

Q: When the level is measured, the leveling instrument to the front view (F, S) and the rear view (B,…

Q: Q- Calculate the corrected staff reading at point A, if the staff reading is taken from an instrumen…

A: Given: The staff reading is taken from an instrument which is set at, A distance, d = 1.5 km. From…

Q: QUESTION 13 The readings shown below were taken to find the height of A, B, C, D, E, F, G and H. a)…

A: To Determine :- a) The adjusted reduced levels for all the pegs. b) The difference of height between…

Q: A vector, F , has components Fx=-228.2 N andFy = 155.4 N. What is the angle made with the…

A: We knowtanα=FyFxα=tan-1FyFxwhere α=angle made with x-axis horizontal

Q: Given: Shaded area below Find: Product of inertia with respect to x- and y-axis (Ixy) y h b

A: to find Ixy of the triangle section

Q: The observed inclined distance performed by stadia leveling is 100 m, and the vertical angle…

Q: 1. The observed interior angles of a triangle and their corresponding number of times measured are…

Q: Calculate degree of static indeterminacy

A: Given data : The number of member in truss m=11 The number of Joint in truss J=7 The number of…

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

A tacheometer was placed at point P to
estimate the horizontal distances PQ
and PR. The corresponding stadia
intercepts with the telescope kept
horizontal, are 0.320 m and 0.210 m,
respectively. The ZQPR is measured
to be 61° 30' 30". If the stadia
multiplication constant =
100 and the
%3D
stadia addition constant =
0.10 m. The
horizontal distance (in m) between the
points Q and R is
[2 Marks]
P
R.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

How to solve for the Taped Distance and Percentage of Error? Show your step-by-step solution.
Determine the magnitude of the resultang.
Determine the y-coordinate of the centroid of the shaded area. y 0.25h 69° 69° Answer:y = i h Save for Later Attempts: 2 of 3 used Submit Answer
What is the the value of the smaller error if point C is 30 meters away from point A and 10 meters away from point B. Point A andB is 40 meters away from each other and the difference in elevation is 2 meters. Rod reading at A Rod reading at B Instrument at C 4.885 1.508
2. The following interior angles of a triangle were measured with the same precision LCD of the No.of Measurements Hint: Weight = %3D No.of measurement of that angle Weight of that angle Angle Error = Total Weight Angle Value No. of measurements A 41° 5 В 77° 6. C 63° Determine the most probable value of angle A b. Determine the most probable value of angle B Determine the most probable value of angle C а. C.
1. In each case, establish a position vector from point A to point B. 1m 3 m -4 m B 3m
The interior angles X, Y, and Z of a triangulartraverse were measured with the same precision. The results were as follows: Station Interior Angle No. of measurement 410 650 750 X 3 Y 4 2 Determine the most probable value of the interior angles.
A horizontal angle is measured five times, and the results are as follows: 156 45 34, 156 45 38, 156 46 30, 156 45 29, 156 45 32 The standard error of the measurement is most nearly A. 8" В. 3" C. 14" D. 4" B.
B1
Please calculate for D and please explain how to input the angle 2°54'13'' in the calculator. D = 1/tan(2°54'13''/2)
Surveying
a) What is the stadia constant of the instrument? b) What is the stadia interval factor? c) What is the horizontal distance between points B & C? d) What is the difference in elevation between B & C? SHOW COMPLETE AND CLEAR SOLUTION AND ILLUSTRATION/FIGURE.