A supply pipe is 1500+(Reg.No/100) ft long, water is initially flowing through it at 2 fps, and the pressure waves travel along it at 3750+(Reg.No/100) fps. For valve closure times of 0.36 sec, find the maximum water hammer pressure at the valve and at 500 ft and 1000 ft from the valve (a) if the valve is completely closed (b) if the valve is partially closed reducing the flow velocity to 0.6 fps.

A supply pipe is 1500+(Reg.No/100) ft long, water is initially flowing through it at 2 fps, and the pressure waves travel along it at 3750+(Reg.No/100) fps. For valve closure times of 0.36 sec, find the maximum water hammer pressure at the valve and at 500 ft and 1000 ft from the valve (a) if the valve is completely closed (b) if the valve is partially closed reducing the flow velocity to 0.6 fps.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

00:44 allll PRACTICE QUESTIONS_GET 214-CLASS 1-2-3.pdf 6 A steel bar 300 mm long, 50 mm wide and 12 mm thick is subjected to an axial pull of 84 kN. Find the change in length, width, thickness and volume of the bar. Take E = 200 GN/m? and Poisson's ratio = 0.32. ôt = 0.0027 mm (decrease), ôV = 45.36 mm' (increase)] 7 A rectangular block 250 mm x 100 mm x 80 mm is subjected to axial loads as follows : 480 kN (tensile) in the direction of its length. 900 kN (tensile) on the 250 mm x 80 mm faces. 1000 kN (compressive) on the 250 mm x 100 mm faces. Taking E = 200 GN/m2 and Poisson's ratio as 0.25 find the following : (i) Change in volume of the block. (ii) Values of the modulus of rigidity and bulk modulus for material of the block. A bar of 30 mm diameter is subjected to a pull of 60 kN. The measured extension on gauge length of 200 mm is 0.09 mm and the change in diameter is 0.0039 mm. Cal- culate the Poisson's ratio and the values of the three modulii. 2 of 2
1. Moment of Inertia of circle having diameter 2 cm is O 0.785 0.885 0.685 O None
Determine the value of centroid (x and y) and moment of inertia (Ix and Iy).
pls answer letter d and e
how to solve the question attached
Please show as many details as possible.
Replace the two forces acting on the bent pipe by a single equivalent force R. Specify the distance y from point A to the line of action of R. Your answer will be positive if the line of action is above point A, negative if below. 110 N 95 mm 215 N 205 mm Answer: y = 125 mm mm
Engineering Mechanics (Please write the complete solutions and FBDs. Solve in 2 decimal places. Box the final answer.)
Solve the problem with complete solution in landscape orientation by placing it in a short coupon bond and avoid erasures. 1. The frames shown in the figure is supported by a hinge at E and A roller at D. Compute the horizontal and vertical components of the hinge force at C as it acts upon BD. 240 D RD A 45° 45 B E REV REH
PROBLEM2a. Determine the centroid of the area shown with respect to the indicated X and Y axes.b. Determine the moment of inertia with respect to the centroidal X and Y axesc, Determine the polar moment of inertiawith respect to the centroidal X and Y axesd. Determine the product of inertia with respect to the indicated X and Y axes
The directrix of the parabola x2 – 4 y = 0 is y =- 5 y = 0 А. В. y = 1 y =- 1 C. D.
st X Test X Test X Test X Test X Tes X Tes X Tes X a06mec101.testportal.net/exam/Do TestQuestion.html testportal Prelim Exams (MEC101) - B06 QuesLIU1I JI 13 (2 p.) The force F has a magnitude of 610 N. Identify the x scalar components of F. Assume F = 610 N, 0 = 29°. F - 534 N 534 N 296 N -296 N here to search