A submersible deep-well pump delivers 250L/min of water through a 1-in Schedule 40 pipe when operating in the system sketched in Fig. 3. An energy loss of 2.3 m occurs in the piping system. (a) Calculate the power delivered by the pump to the water. (b) If the pump draws 1 hp, calculate its efficiency.

A submersible deep-well pump delivers 250L/min of water through a 1-in Schedule 40 pipe when operating in the system sketched in Fig. 3. An energy loss of 2.3 m occurs in the piping system. (a) Calculate the power delivered by the pump to the water. (b) If the pump draws 1 hp, calculate its efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You and your workmate are choosing pumps for your design. You've already decided which centrifugal pump you will use. The next thing you would think about this time would be the shape of it's impeller blades. The impeller in your design would have a revolution of 565 rpm, will have a volume flow rate of 11.7 gals per min and will (discharge) head of 2222 cm. Your coworker said that axial flow pump is your choice. Would you agree? Why or why not? Prove it.
For the single pump-pipe system below, what will be the changes for the operating point if we increase the pipe size but decrease the shaft speed of the pump? EB H₂ O The operating point will remain the same. O The operating point will occur either at a higher discharge or at a lower discharge, depending on the specific influence of each change. O The operating point will occur at a higher discharge. O The operating point will occur at a lower discharge.
Determine the power requirement of the pump shown in Figure 3.0, assuming it has an efficiency of 88%. The system has a loss coefficient of 3.0 up to point A, and K =1.2 from point B to point C. Neglect any losses through the exit nozzle. Additionally, compute the pressures at points A and B. Water 15 m 2 cm 4 cm dia. 5 cm dia. Figure 3.0 400 kPa
4.32 ft 24.5 ft 7.47 ft O Air at 29.4 psig pump A pump delivers water from a lake into a 6 ft diameter by 10 foot tall sealed pressurized tank through 4 inch pipes using a 4.0 horsepower pump with an efficiency of 62%. If the head loss through the system is 6.42 ft, determine the delivery rate (m3/s) of water to the tank, for the tank level and pump pressure shown in the drawing.
The system in Fig 2 pumps water from a lower reservoir to a higher reservoir. The pipe diameter is 0.235 m and the pipe lengths are L1= 5 m, L2= 4.5 m, L3= 1.5 m, and L4= 0.6 m. The impeller of the centrifugal pump has a diameter of 0.55 m and operates at 850 rpm. The uniform blade height is 51 mm. The water enters the pump parallel to the pump shaft with a flow rate of 0.16 m3/s. Take viscosity as 0.00112 N s/m2. Fig Q2: Piping system to pump water between two tanks. Work to 4 significant digits. Enter all values using base units or their combinations, i.e. m, m/s, Pa, N. Do not use multiples as e.g. mm, kPa. You can use values with exponents, such as 0.12e3. a) What would be the shaft power required to turn the impeller if the exit blade angle is 31 degrees. b)
In order to meet the stated goal of delivering 4 gallons per minute at a height of 670 meters, a single pump must have a maximum flow rate of 40 gpm. How many stages are needed if the speed cannot exceed 1352 rpm?
Q3
1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)
Calculate the NPSHA in ft for the following configuration of a pumping system. Pv=924.8Kpaa ... Vessel Pressure = 134.6 psia Minimum Operable Liquid Level 15 ft Water, 350F Datum Suction Line Losses = 5 ft (1.52m)
Topics: Fundamental of fluid flow Oil (SG=0.82) entering a pump through an 8-inch diameter pipe at 4 psi has a flow rate of 3.5 cfs. It leaves the pump through a 4-inch diameter pipe at 15 psi. Assuming that the suction and discharge sides of the pump are at the same elevation, find the horsepower delivered to the water by the pump (550 lb.ft/s = 1 HP). Illustrate the problem and show your complete solution.
Patrick is building a cabin on a hillside and has proposed the water system shown below. The distribution tank in the cabin maintains a pressure of 27 psig above the water. There is an energy loss of 14.6 lb*ft/lb in the piping. When the pump is delivering 37 gal/min of water, compute the horsepower delivered by the pump to the water. PA = Submit Question Distribution tank 4 ft Flow hp 214 ft Pump 1 ft
Title of the book: Fluid Power, Theory and Applications, 3rd Edition, James A. Sullivan