A student wants to measure the current through the resistor R for the circuit below. R2 A R, Where should a student hook up an ammeter to measure the current through R?

Q: What is the smallest square box that will accommodate four No. 12 conductors and four No. 10…

A: conductor A conductor is any piece of material that easily allows heat or electricity to pass…

Q: What do call to the encircle part of socket and what is the purpose?

A: It is a 3 pin plug. There are three wires in a 3 pin plug named as- 1 – Earth -E 2 – Neutral -N 3 –…

Q: Explain briefly, the Professional Code of Ethics of an Electrical Engineer.

A:

Q: A single-phase 60-Hz power line is supported on a horizontal crossarm. The spacing between…

A: Distance between power conductors is 8ft.The distance between telephone conductors is 2ft.

Q: Find the appropriate conductor size for a THHN copper wire with 75 deg Celsius temperature capacity…

A: Note: For THHN wire rated at 75 degree Celsius, National Electric Code table should be followed…

Q: Explain insulation coordination

A: Coordination is required in electrical systems for proper functioning of the equipments. Insulation…

Q: 70. A circuit supplies a continuous load of 38 amperes and is protected by a 50-amperecircuit…

A: While calculating the conductor size for a continuous load, take 125% of overloading conditions…

Q: List the different Wire Gauge and its uses. Note: Typical wires at home.

A: The wire gauge is used to measure the diameter of the wire. The measure of electric flow the wire…

Q: What is UPS in electrical engineering?

A: Full form of UPSUninterruptible power supply

Q: The curent in a 0.05-H inductor is I= 42 – 30° A. If the frequency of the current is 60 Hz, what is…

A: The equation of the current in time domain is: I(t)=4cos(ωt-300)A The inductor value is L = 0.05H…

Q: Which sub-atomic part of an atom is used as a fundamental unit of electricity par'icularly when it…

A: 1.answer: C electron  Electron is the fundamental particle which causes current. While remaining…

Q: * Experiment No3:- Loaded operation of the Dc Series Gen-erater H.W.:- who is the Best shunt or…

A:

Q: A DC motor that draws 7.2A is located 85 feet from its 240VDC source. The copper conductors…

A: Given Voltage V = 240 V Current I = 7.2 A Length L = 85 ft Voltage drop = 2%

Q: Discuss any two types of grounding methods.

A: Two types of grounding methods: Solid grounding Resistance grounding

Q: Develop a LabVIEW code (Front panel and Block diagram) of a wire cutting system

A: LabVIEW code for a wire cutting system. However, please note that without specific requirements or…

Q: s an Electrical Safety person, exposed wires should be recognized as a hazard. Evaluate the risk…

A: In an electrical system, an exposed wire can a person in a situation of danger. Exposed wires may…

Q: A 40 amp branch circuit is run a long distance requiring a voltage drop calculation which increases…

A: To determine the proper size for the copper equipment grounding conductor in a 40-amp branch…

Q: where is it most convenient to find a PKES system

A: We need to tell about PKES .

Q: Part 2: Analysis and selection of the Wind Turbine. The team decides at install a 30 MW wind farm.…

A: 1: Analysis and selection of the Wind Turbine.The team decides to install a 30 MW wind farm. The…

Q: Kirchhoff's current law (KCL) is mostly to be applied to: Select one: a. A circuit that are mostly…

A: Kirchhoff's Current Law: Kirchhoff's first Law is based on the law of conservation of change, which…

Q: Question 5- Power Network, Frequency & Connected Load a) In the UK and many other countries, there…

A: The legal requirement to maintain the voltage and frequency with permitted tolerances is due to the…

Q: You are an electrician working in an industrial plant. The company is constructing a maintenance…

A:

Q: Draw the block diagram representation of a heating system.

A: Answer- Block diagram of heating system -

Q: How equation is obtained ? is that equation given in the textbook ?

A: That equation is the direct formula of pulse spread. And no need of derivation of the equation.…

Q: A wiring job requires 7,645 feet of cable. If the cable comes in 250 ft. coils, how many coils of…

A: Given: The total length of the cable required is 7645 feet.  The length of a cable coil is 250 feet.…

Q: What NEC article contains a list of the electrical installations that are covered by the NEC?…

A: The NEC (National Electrical Code) is a globally recognized standard for the safe installation of…

Q: Tan delta and partial discharge diagnostics are the most common electrical testing techniques used…

A: Tan delta testing: In high voltage cable insulations in practical conditions, there exists a…

Q: Describe the job of the Board of Electrical Engineering in one sentence.

A: The solution is given

Q: Q6) Explain by drawing a block diagram of a power supply?

A: Draw the block diagram of the Regulated power supply.

Q: V1 Op-amp V; = 0 Rf R1 R1 Fig. 3.11 (a) Non-inverting amplifier (b) Equivalent circuit with virtual…

A:

Q: With the help of schematics, briefly describe, how a telephone set works.

A:

Q: With a neat diagram indicating all the parts, explain the working of the nuclear power plant. (Any…

A:

Q: A pvc raceway has multiple circuits installed. The circuit sizes are 20 amp 60 amp and 100 am. A…

A: To determine the appropriate size of the equipment grounding conductor (EGC) for a PVC raceway…

Q: if i use Voltage division instead of nodal analysis. where do you suggest i start, and How do I…

A:

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.