A stream of water with density p=1000 kg/m³ is discharged from a nozzle at the rate of 0.085 m³/s as shown in the figure given. Using Bernoulli's equation, the gage pressure P in the pipe just upstream from the nozzle is P = (v - v). Knowing the nozzle is held to the pipe by six flange bolts, determine the tension in each bolt, neglecting the initial tension caused by the tightening of the nuts.

A stream of water with density p=1000 kg/m³ is discharged from a nozzle at the rate of 0.085 m³/s as shown in the figure given. Using Bernoulli's equation, the gage pressure P in the pipe just upstream from the nozzle is P = (v - v). Knowing the nozzle is held to the pipe by six flange bolts, determine the tension in each bolt, neglecting the initial tension caused by the tightening of the nuts.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The diameter of a pipe gradually reduces from 1 m to 0.7 m. The pressure intensity atthe center line of 1 m section is 8and rate of flow of water through the pipe is600 liters/s.,I. Find the intensity of pressure at the center line of 0.7 m section.II. Determine the force exerted by flowing water on transition of the pipe.
According to Torricelli´s theorem, the velocity of a fluid discharging through the hole of a reservoir is V=(2gh)^1/2, where h is the height of water above the hole, as shown in the figure. If the hole has a section Ao and the reservoir is cylindrical with a cross-section of area Ab>>Ao. Obtain a formula for the time it will take for the reservoir to completely empty if the initial height of the water is ho.
A pipe of diameter 10cm conveying 200 liters/s of water has bend of angle (θ = 90⁰) and θ = 0⁰ through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively
Water flows through a circular pipe with a 180° elbow and exits to the atmosphere through a nozzle as shown in the figure. The diameter of the pipe is 300mm and the diameter of the nozzle exit is 160mm. The density of water is 1000kg/m3. The pressure gauge at the front of the pipe (section 1) reads 60kPa. Find the force of the upper, middle and lower bolts at the flange joint at section 1 position. Assuming that four bolts are installed at the up, down, front and back, the cross-center distance of the four bolts is 150mm and the weight of the elbow and the water is 100N. Z1 is 0.3 m.
(3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank has a circular cross section of diameter D and the flow exit has a circular cross section of diameter Do. Do not assume that H(t) is constant. The fluid has density p and the exit is open to the atmosphere. Wall H D- Do Cable Vo (1) Determine H(t) and the exit velocity Vo(t). (2) Determine the tension in the cable as a function of time Your answers should be in terms of given parameters (D, Do, p, g) о,
Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 cm2, ρ1=1878 kgm/m3. At exit: A2=10 cm2, ʋ2=249.5 cm3/g, ῡ2=3048 cm/min. Determine the following: ḿ1 in g/min ῡ1 in m/min
A pipe of diameter 11 cm conveying 200 liters/s of water has bend of angle (θ = 90⁰if last digit is zero/even and θ = 0⁰ if last digit is odd) through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively.
A water jet of an area of 0.03 m² impinges normal on a fixed plate. If a force of 1 kN is produced as a result of the impact, the velocity of the jet would be
Q1(a) 150 litres per second of water is flowing in a pipe having an inlet and outlet diameter of 250 mm and 200 mm respectively. If the pipe is bent by 120° as shown in Figure Q1(a), by taking the momentum flux correction factor as 1.08, determine: (i) the pressure at the outlet, if the inlet pressure is 40 kPa; (ii) the anchoring force in x-axis (F;) required to hold the pipe; (iii) the anchoring force in y-axis (F) required to hold the pipe. Outlet 1.3 m 120° Inlet Figure Q1(a)
A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50 g and is charged with 100 g of water. The pressure inside the rocket is 100 kPa gage. The exit area is one-tenth of the chamber crosssectional area. The inside diameter of the rocket is 5 cm. Assume that Bernoulli's equation is valid for the water flow inside the rocket. Neglecting air friction, calculate the maximum velocity it will attain. 5 cm PROBLEM 6.90 100 kPa
In a tapered horizontal pipeline, the seawater's speed is 3.75 m/s and the gauge pressure is 21 kPa at the first point. Find the gauge pressure at a second point in the line if the cross-sectional area at the second point is thrice that at the first.
A tank with radius (1m) and a height of (4m) is initially filled with water. Then the hole at the bottom of the tank (shown in the figure) is opened and the water flows out by gravitational. Find the time required to fill an (8 m³) vessel below the tank. • Use the gravitational acceleration g = 9.807 m\sec². R= 1 m 2 m 2 m Cd = 0.9 a =2 * 10-3 m? Vessel of 8 m3