A storage reservoir supplies water to a pressure turbine under a head of 20 m. If the flow rate is 500 liters per second the head loss in the 300 mm pipe supplying the turbine is 2.5 m. Determine the pressure at the entrance of the turbine. If a negative pressure of 30 kPa exists at the 600 mm diameter section of the draft tube (exit tube) below the turbine 1.5 m below the supply line, estimate the energy absorbed by the turbine in kW neglecting losses between the entrance and exit of the pipe. Find also the output of the turbine assuming an efficiency of 85%. *can you also provide its figure

Q: Calculate the average velocity of water in the pipe?   2. Determine the Reynolds number in the…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: A horizontal 154 mm diameter pipe gradually reduces its section to 53 diameter, subsequently…

A: Pipe diameter at the inlet, d1=154 mm=0.154 mPipe diameter at the section 2, d2=53 mm =0.053…

Q: In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be…

A:

Q: Air flows through the 400-mm-wide rectangular duct at 75000 liters/min as shown in . Take pa = 1.202…

A:

Q: A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

A:

Q: Water at 200∘F enters the radiator at A with an average velocity of 4 ft/s and a pressure of 60 psi.…

A: given data for a radiator Vavg=4ft/spa=60 psi…

Q: A horizontal 150 mm diameter pipe gradually reduces its section to 50 mm diameter, subsequently…

A: Bernoulli's principle states that the flow energy of liquid before entering a section will be equal…

Q: Determine the pressure at the entrance of the turbine. If a negative pressure of 30 kPa exists at…

A:

Q: The 20mm diameter commercial steel pipe, 30 m long is used to drain a water tank. The water level in…

A: Diameter of the pipe, D= 20 mm= 0.02 m Length of the pipe, L= 30 m Height of the water level in the…

Q: Part B Taking in your consideration the head losses accumulated by the fluid when flowing in the…

A:

Q: A storage reservoir supplies water to a pressure turbine under a head of 20 m. If the flow rate is…

A:

Q: A pump delivering 230 lps of water whose absolute viscosity is 0.0114 Poise has a 300-mm diameter…

A:

Q: calculate the power (kW) delivered by the pump

A: Need to calculate the power.

Q: A horizontal 150 mm diameter pipe gradually reduces its section to 55 diameter, subsequently…

A:

Q: Question 1: The diagram shows water leaving a tank through an inverted V-tube. y (D (All answers to…

A:

Q: 8. Given the following venturi meter and the two pressures shown, calculate the mass flow rate of…

A: As per given question we have defind Mass of flow rate of in the circular pipe?

Q: Example the bottom and upper end respectively. The intensity of pressure at the bottom end is 350…

A: The entire mechanical energy of the flowing fluid, which includes the gravitational potential energy…

Q: What type of fitting is being uscd when the fitting experiences a head loss of 2.012 ft while the…

A: Given: Head loss of the fluid is 2.012 ft. The velocity of the fluid is 12 ft/sec.

Q: Ex. 2.1] A pump delivering 230 Ips of water whose absolute viscosity 300-mm diameter suction pipe…

A: Fluid is a state of matter which deforms continuously on the application of the external force,…

Q: The 150 mm pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Q: A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degrees…

A:

Q: A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

A: Given data: D=300 mmd=100 mmP=150 kPaHead loss=3% of differential pressure headhloss=-400 mm Need to…

Q: The velocity of the liquid flowing through the rusty iron pipe having a 150 mm diameter is 2.5 m/s.…

A:

Q: 2) Determine the Reynolds number in the pipe system and the significance of this Information?

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: 4. Determine the pressure required, in psi, in the pipe just ahead of the nozzle shown in the figure…

A: Given jet velocity v2= 75 fps diameter d1= 1 in  diameter d2 = 0.75 in

Q: Water (@ 45°C) is flowing in a horizontal pipe with an increasing cross-sectional area. The measured…

A: Given   Pressure drop = 4.1 psia                            = 28268 Pa         Exit area, A = 2a…

Q: Oil of specific gravity 0.802 and kinematic viscosity 0.000186 m /s flows from tank A to tank B…

A:

Q: Calculate the flow rate of the system by accepting the fluid passing through the reservoir-pipe…

A:

Q: The flow rate of the system is 1 cubic meter per second. Determine the major and minor losses of the…

A: The flow rate of the system, Q=1 m3/s=35.3147 ft3/s                                       1…

Q: The head loss at the entrance of the pipe is similar to O Sudden contraction head loss O Sudden…

A: Solution:

Q: A custom pipe connection was installed to deliver water to the highest level of a commercial…

A: given data; ⇒discharge at A (QA)=100lps=0.1m3/s⇒discharge at C(Qc)=40lps=0.04m3/s⇒discharge at B…

Q: Water is flowing at a rate of 12 ft^3/s, and it is assumed that the head loss from the reservoir to…

A:

Q: A pipe with a cross sectional area of 5x10 m' is delivering oil at a rate of 1x10 m/s at a pressure…

A:

Q: The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank…

A: According to the problem, the water is siphoned out of the tank so the pressure at the end where the…

Q: A Kaplan turbine develops 1500 kw under ahead of 6 m. the turbine is set 2.5 m above the tail race…

A:

Q: A pump at an elevation of 300m is pumping 0.05 m³/s of water through 2.4 km of 150-mm pipe to a…

A:

Q: Determine the rate of flow of water through a pipe of 300 mm diameter placed in an inclined position…

A:

Q: In the test of the reaction turbine, the water flowing over the weir in the tailrace was found to be…

A:

Q: Water from a reservoir is pumped over a hill through a pipe 3 ft. in diameter, and a pressure of 35…

A: Given Data : pressure at summite=35 psi pumped quantity = 55cfs pump above resorvoir=300 ft head…

Q: When 0.042 m3 /s of medium fuel oil flows from A to B through 1067 m of new 150-mm uncoated cast…

A: Given:Volume flow rate,Q=0.042 m3/sD=150 mmhead lost, hL=44 mPressure:pB=345 KPazA=0 mzB=18.3 m

Q: Determine the elevation that the 240 mm diameter pump can be situated above the water surface of…

A:

Q: Determine the rate of flow of water through a pipe of 300 mm diameter placed in an inclined position…

A: The volume flowrate of fluid passing through a cross section can be determined as the product of…

Q: Hydraulic oil flows through the system shown so that the velocity delivered at B is 67 ft/sec. The…

A: Given Data, Taking  datum line is the centerline of 10-in schedule 40 steel pipe VB = velocity at…

Q: When the valve at A is closed, the pressure at A is 232 kPa and at Bit is 180 kPa When the valve is…

A:

Q: The 150 mm pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Q: The 150 mm pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Q: The 150 mm pipeline as shown conducts water from a reservoir and discharges at a lower elevation…

A:

Q: A fluid having v = 4x10^-5 m2/s flows in a 750 m long pipe having a diameter of 20 mm.  Determine…

A: Given data:  Kinematic viscosity, ν=4×10-5 m2/s Length of pipe, L = 750 m Diameter of pipe, d = 20…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.