a steel tape of nominal length 200m with a plumb bob of mass 16kg attached to it was used to measure a length down a shaft as 160.852m. the mean temperature during the measurement was 4'C. if the tape was standardized to be 200.0014m under a tension of 115n at 20'C temperature, determine the correct measured length

Q: A tape 30 m long, 0.6 cm wide and 0.5 thick was used to measure a distance of 000 m at a temperature…

A: Given- Measured distance Lm=999.75 mStandard temperature To=20o CField temperature T=35o CActual…

Q: Calculate the shear modulus for a given cylindrical metal speciman and test results of T = 1500 N…

A:

Q: Q2: - A tape 100m long. it's cross sectional area in 0.0585 cm, the apparent length of which was…

A: Length L = 1500 m = 150000 cm Area A = 0.0585 cm2 Standardised pull Ps = 6.75 kg Actual Pull P =…

Q: Bar Sample No. deformed deformed Туре Nominal Diameter, mm 1 25 12 12 12 Average Diameter, mm…

A: Given data, Elongation of 2nd bar = 33.25 cm Change in length of 2nd bar = 3.25 cm Change in length…

Q: The figure shows a system of 3 steel wire, each with an area 0.05 in? , used to lift a load W=1,500…

A:

Q: y 53 mm 85 mm 25 mm 57° 25 mm - b 65 mm

A:

Q: Part A Determine the moment of the force about point O. Neglect the thickness of the member. Assume…

A: To calculate the moment of force at point O, resolving the force in X and Y direction and then…

Q: Q- 7 b, A bar specimen of 36 mm diameter is subjected to a pull of 90 kN during a tension test. The…

A: Given data- A bar specimen- Diameter d=36 mm, Change in diameter ∆d=0.0046 mm, Gauge length L=200…

Q: e right solutio

A: Given Figure Given data A=150mm2 E=180GPa L=4m P=50kN Draw Free body diagram

Q: The isosceles triangle gate shown in the figure is hinged at A, and weighs 1500N. Find the location…

A: Consider the following figure:

Q: 3. A line was found to be 2,850 m long when measured with a 50-m tape under a steady pull of 5.5 kg.…

A:

Q: The beam is subjected to a shear force of 180 kN (Figure 1) Part A Determine the shear stress…

A: Given: The shear force in the beam is 180 kN. Consider the figure.

Q: Problem-3 A solid steel sphere having modulus of elasticity of 200GPa and poission's ratio of 0.25…

A: Given- Modulus of elasticity E=200 GPa, Poisson's ratio μ=0.25 Volume reduced by 0.3%, Hydrostatic…

Q: A smooth ceramic sphere (SG = 2.6) is immersed in a flow of water at 20°C and 55 cm/s. What is the…

A: A Reynolds number is a dimensionless quantity that determines whether a flow pattern is laminar or…

Q: Calculate unknown force

A: This question is from solid mechanics

Q: 3B. A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine…

A: Determine the total change in length of the bar

Q: A steel tape is 100m long at 60oC with a pull of 10 kg. A line was measured and found to be 510.02m…

A: Consider the given data L=510.02 mα=0.0000065 /oCTo=60oCTm=65oCPo=10 kgP=10 kg For calculating the…

Q: Determine the volume V and total surface area A of the solid generated by revolving the area shown…

A:

Q: For a 10-meter rod made of the material with Poisson's ratio v= 0.3, that has elongated by 12 mm,…

A: Elongation ∆l=12 mm Length l=10 m = 10000 mm Poisson's Ratio ν=0.3 Initial Radius= 50 mm Initial…

Q: Ex.1': A Newtonian fluid having a specific gravity of 0.92 and a kinematic viscosity of 4*10 m/s…

A:

Q: From the figure below with the given parameters A 03 D W 2 W1 W1 501 N e1 120 e2 690 e3 430…

A:

Q: 14 100 lb Given the space force below, what is its x-component? 8. O A. 87.4 lb to the right O B.…

A:

Q: A steel bar of cross-section 500 mm2 is acted upon by the forces shown re. Determine the total…

A: Given, Cross-section (A)= 500 mm2 Modulus of elasticity (E) = 2 × 105 N/mm2 For determining the…

Q: Step by step solution, neat and clean handwritten and show FBD if possible.

A:

Q: The 3.6-kg slender rod is initially supported horizontally by a spring at B and pin at A (Eigure 1)…

A: ASKED: To determine- angular acceleration of the rod at the instant the force is applied…

Q: Steve Roger measured a line and found it out to be 950 m long using a 20 – m tape under a steady…

A:

Q: f 0.0000116 m / °C is known to be 50m long at 20°C. The tape was used to measure a line which is…

A:

Q: A 30 m steel tape exactly at a temperature of 20° C and pull of 10 kg were used in a practical class…

A:

Q: Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa.…

A:

Q: Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in…

A: Shear stress is the amount of loading which gets sheared in the beam or any structural element by…

Q: A line was determined to be 2395.25 m when measured with a 30-m steel tape supported throughout its…

A: Given data- Pull applied in field (P) = 4 kg Standard pull (Po) = 5 kg Measured length (L) = 2395.25…

Q: How to get TEC and TBC

A: Given data  0.77TEC + 0.8TBD = 1440...........(1) 0.514TEC - 1.6 TBD = 0...............(2)

Q: A 50 m. tape of standard length has a weight of 0.05 kg/m, with a cross sectional area of 0.04 sq.…

A: Given riangle t =18-20=-2 c C=0.00000116 L=458.65 m Tape length =50 m

Q: DIAMTER IS 50mm IS LOADED BY AN ALUMINUM SHAFT WITH A COSNTANT TORQUES APPLIED TO GEARS ATTACHED TO…

A:

Q: A tape of 20m length is used to measure a distance 1980 m at a temperature 35 °C under 20 N tension…

A: Given Data Length of the tape=20 mThe diatance measured=1980 mTemperatureTm=35°CTension ForceT1=20…

Q: Prepare and complete the differential level notes for the information shown in the accompanying…

A: To complete the given differential level notes and perform the arithmetic check.   Given: STA BS…

Q: Question 1 : Answer question A and B   A- If the pressure potential is zero and it is 20-20 cm,…

A: solution: For part A: h1 = 20; h2 = 20cm Pressure Potential is Zero pg=po+hpg=0m=45kgh=mAp=…

Q: When a bar of certain material 40mm square is subjected to an axial pull of 1,60,000N the extension…

A: From question,Axial load ,P=160000 NCross section area,

Q: Find ?? (epsilon x), ??  (epsilon y) and ? (gamma) . NOTE: ?? (epsilon x) ??? ?? (epsilon y) in…

A:

Q: Q#3: A steel Tape was exactly 30m long at 22°C when supported throughout its length under a pull of…

A:

Dependence on mechanical properties

The mechanical properties of materials are those structures that include the reaction to the load used. Metal switching features determine the scope of the usefulness of the content and establish the expected service life. Machine structures are also used to help distinguish and identify material objects. The most common mechanical properties considered are strength, ductility, stiffness, impact resistance, and resilience to fractures.