A steel spur pinion has a pitch of 6 teeth/in, 22 tooth full-depth teeth with a cut profile, and a 20 pressure angle. The pinion runs at a speed of 1,160 rev/min and transmits 17.434 hp to a 60 tooth gear. of the face width is 2 in., estimate the static bending bending stress in the gear ooth in psi. Use the Lewis equation. Take the value of Lewis form factor, Y, from the table 14-2. Note do NOT use the elocity factor Kv in the bending stress equation.

Q: A 20 degree pressure angle spur gear set is transmitting 10 horsepower at 1,000 RPM. The pinion has…

A: The pressure angle = 20 degrees The horsepower, P = 10 hp the speed of the gear, N = 1000 rpm The…

Q: aight Spur geard, having 20 involu telk full de pth teerh is to halre tvanjmitted Power 12 KW at 3ne…

A: assume y

Q: A 20° full-depth steel spur pinion has a diametral pitch of 5 teeth/in and 24 teeth and transmits 6…

A:

Q: A 17-tooth 20° pressure angle spur gear rotates at 1800 rev/min and transmits 4 hp to a 52-toot…

A: dp=NpPd=1710=1.7 indG=5210=5.2 inV=πdp.np12=π×1.7×180012=801.1 ft/min

Q: Problem 4. A 16-tooth 240 Bhn steel spur pinion having a pressure angle of 20° and rotating at 720…

A: Calculate the diameter of the gear. Dg=NgPg Here, Dg is the gear diameter, Ng is the number of teeth…

Q: 13-31 Shaft a in the figure has a power input of 75 kW at a speed of 1000 rev/min in the…

A: Given, Power in shaft a = Pa = 75 kW = 75000 W Rotational speed of a = Na = 1000 rpm Module of all…

Q: pitch of 4 teeth/in, a 2 inch face, 20 teeth, and a pressure angle of 20° with full depth teeth. The…

A: the term moderate applications seems to imply that the gear can be rated by using the yield strength…

Q: Q/A steel spur pinion and gear of grade 1 have a diametral pitch of 11 teeth/in , shaped profile…

A:

Q: A double-thread worm has a pitch diameter of 3 inches. The wheel has 20 teeth and a pitch diameter…

A:

Q: A 20° spur pinion with 20 teeth transmits 120 W to a 36-tooth gear. The pinion speed is 100 rev/min,…

A:

Q: The shaft rotating at 550 rpm carries a spur gear B having 96 teeth with a diametral pitch of 6 and…

A: Given data as per the question Speed of shaft =550 rpm No. of teeth on gear B =96 Diametral pitch =6…

Q: campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km=…

A:

Q: PROBLEM 2. The turbine in the figure generates 90 kW power. 50 kW of power is drawn from the gear at…

A: Total Power P = 90kW  Power with gear C Pc = 50kW = 50×103 W Power with gear D PD = 40kW = 40×103 W…

Q: A planetary gear used on the Mars rover uses a 25-tooth helical gear with ψ = 20° has a 25° pressure…

A: Given Data The number of tooth are: N=25 The angle of the thread is: ψ=20° The pressure angle is:…

Q: A 20° 20-tooth cast-iron spur pinion having a module of 4 mm drives a 32-tooth cast-iron gear. Find…

A:

Q: A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth…

A: Answer: (a) Normal circular pitch: 0.4335 in (b) Normal diametral pitch: 7.2470 in (c) Axial pitch:…

Q: The figure shows a 10 diametral pitch 18-tooth 20° straight bevel pinion driving a 38-tooth gear.…

A: The diametral pitch, Pd = 10The number of tooth on bevel pinion, z = 18 toothThe pressure angle = 20…

Q: cast St gear angle has to 33 kW at 2000 r.p.m. If the gear has 25 teeth, find the necessary module,…

A: In helical gear the teeth of the gear remains in the form of helix around the gear. There is a…

Q: 1. A 10 inch pulley transmits 3 kW to a 17 mm diameter transmission shaft at 500 rpm through an 5 mm…

A: As per guidelines we need to answer only first question, so please re-post rest questions separately

Q: 3. A double-threaded right-handed worm gear transmit 15-hp at 1150 rpm. The pitch of the worm is…

A:

Q: - number of teeth ower of 3 kW at 2

A:

Q: The figure shows a 16T 20° straight bevel pinion driving a 32 T gear and the location of the bearing…

A: Given data ;Power = 2 HpSpeed (N) = 200 rev/minr=2 inch

Q: ExJA 20° straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a…

A:

Q: An epicyclic reduction gear shown in figure, has a shaft A fixed to arm. The arm has a pin fixed to…

A:

Q: etral pitch,

A: 20°hp=15hpnp=1750rpmDp=4-inmw=4 To-Find:-   A.Determine the diametral pitch,  B. face width,   C.…

Q: An electric motor transmits 0.5HP at 1600RPM. A 100 tooth helical pinion having a normal pressure…

A: Power transmitted by the motor is 0.5 HP= 373 watts Rotation per minute of motor is 1600 Normal…

Q: The 241 6-pitch 20° pinion 2 shown in the figure rotates clockwise at 900 rev/min and is driven at a…

A: Given data: 24T  6 pitch 20° pinion 2 rotates clockwise at 900 rev/min power of 28 hp h=28hp gear…

Q: A gearset has a module of 5 mm, a 20 degree pressure angle, and a 24-tooth cast iron spur pinion…

A: Given-Information: Module = 5 mmPressure angle = 20°Number of tooth on pinion(Zp)=24Rotational speed…

Q: of 1.5. Check for yielding. Check the slopes at the bearings for satisfaction of the e that the…

A: The tension .The design factor is .The notch radius is .

Q: 1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW,…

A: Given : P = 7.5 kW N = 1450 rpm u = 2.08 To find : Design pair of spur gears Note : some values are…

Q: A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth…

A: (a) Normal circular pitch: 0.43354 in (b) Normal diametral pitch: 7.24637 teeth/in (c) Axial pitch:…

Q: A bevel gear receives a power from bevel pinion results in the shown forces. The forces are F =…

A:

Q: A compound spur gear train with teeth as indicated in the figure with a module of 12mm and a…

A:

Q: = A straight bevel gear pair has the following data: Np 25; NG 50; P = 10; and 20° pressure angle.…

A: given;

Q: A 35 kW motor running at 1200 rpm drives a compressor at 780 rpm. The arrangement is made through a…

A: From the given data,

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.