A steel sleeve coupling (see the figure below) is designed to join 2 externally threaded members. Make proper assumptions and calculate the minimum thread diameter if the joint is loaded by axial static force F=30 kN. Materials used have o, = 355 MPa. The safety factor should be 2. F

A steel sleeve coupling (see the figure below) is designed to join 2 externally threaded members. Make proper assumptions and calculate the minimum thread diameter if the joint is loaded by axial static force F=30 kN. Materials used have o, = 355 MPa. The safety factor should be 2. F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Given the configuration in Figure 1, calculate the load that can be supported under the following…

A: GIVEN; Pin diameter =10 mm =0.01 m Ultimate strength σut = 195 MPa FOS =2 Strength of cable = 207.5…

Q: A bolted lap joint using ISO class 5.8 bolts members made of cold-drawn SAE 1040 steel own in the…

A: Given Diameter, d = 20 mm Factor of safety, f = 2.5 Find Tensile shear load, F

Q: the diagram below shows a circula bar , made of AISI 1040 OQT 1300 steel (SU = 600 MPa), is loaded…

Q: Two metal plates, are joined as show below. Using standard material values, complete the following:…

A: To Find : The suitable diameter , Given : The load is P=150kN. The shear strenght of aluminium is…

Q: kle joint, that shown in the figure below, is used to transmit ring the various failure cases of the…

Q: calculate the maximal force F which can be applied to the couplin

A: fot solution refer below images.

Q: A cover of a boiler shall be fastened with 6 studs. The pressure in the boiler is 40 bar. The…

A: Disclaimer: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Urgent

A: Given:-

Q: An M30 x 3.5 ISO 8.8 bolt is used in a joint at recommended preload, and the joint is subject a…

A: Introduction Bolted joints are a collection of fasteners and nuts used to unite two things into…

Q: Problem 3. The tension lock shown at the figure below will be loaded by an axial force F = 10 kN.…

Q: Required information A rotating shaft of 25-mm diameter is simply supported by bearing reaction…

A: Given data: ● The load applied on the beam: W = 13 kN ● The diameter of the beam: d = 25 mm ● The…

Q: A course pitch metric grade 9.8 bolt with a hexagonal nut assembly is used to keep two machined…

A: Step 1: Step 2: Step 3: Step 4:

Q: M8x1 SAE 9.8 Bolts A B C P 100 D E F. 150 H I 100 100--100-80 400 A bracket is bolted onto a channel…

A: Given Bolt diameter = 8 mm To find Maximum load For bolt A, C, G, I For all the bolts Verify does…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M16 × 2-…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: Use LRFD and design a welded connection to resist the available strength of the tension member in…

A: Drawing the plate with the dimensions ,

Q: The figure shows a connection that employs three SAE grade 4 bolts. The tensile shear load on the…

A: From Table 8-9: for SAE Grade 4 boltsFrom Table A-20: for AISI 1020 HR

Q: A butt connection is shown in the following figure. Plates is Q235 steel; 8.8 Grade M16 high-…

A: Load bearing capacity Loadbearing capacity is the maximum ability of a structural member or…

Q: high pressure boiler accumulator are fixed using a number of bolts of M16 × 2- C, grade 5.8, with…

Q: (7) A universal joint shown has a pin whose Sy = 485N/mm2 & d = 15mm. Its pin-bush has a length a =…

Q: 8-48 A vertical channel 152 x 76 (see Table A-7) has a cantilever beam bolted to it as shown. The…

A: 1

Q: The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load…

A: Given kb = 8 Mlb/in km = 18 Mlb/in Bolt Size = 5/8 in Fatigue design factor = 2.5 To find Repeated…

Q: 10) A screw clamp similar to the one shown in the figure has a handle with diameter in made of…

A: Given Screw clamp To find Torque it can handle

Q: How many bolts are required for LRFD and ASD for the bearing-type connection shown, if PD = 50 k and…

Q: (11) The figure shows a connection that employs three SAE grade 5 bolts. The tensile shear load on…

Q: repeat problem 8-19 with the bottom aluminum plate replaced by one that is 20 mm thick.

A: The total grip length is the sum of the thicknesses of the plates being clamped together. In this…

Q: A 25 mm diameter steel bar is loaded in double shear until failure, the ultimate load is found to be…

Q: The weld joint in the figure is 2nd quality. Since V1=0.8 V2=0.8 Kkç=1.5 Ky=0.85 Kb=0.82 σAk=300…

A: Write the given data in the problem. V1=0.8 V2=0.8 Kkc=1.5 Ky=0.85 Kb=0.82σAC=300 MPaσCD=200…

Q: The figure shows the handle super fast byke and its geometry with forces The cross section at the…

A: Given data Major axis = 3in Minor axis = 1.5in Load = 20kip To estimate Stresses of the inner…

Q: Design a rigid type flange coupling to connect two shafts in order to transmit torque. The input…

A: Given data: Rated power = P = 20 HP = 20 * 745.7 W = 14914 W Rated speed = N = 200 RPM Factor of…

Q: 8-68 esign 40 70 40 + A bolted lap joint using ISO class 5.8 bolts and members made of cold-drawn…

Q: A cantilever is to be attached to the flat side of a 6-in wide channel used as a column. The…

A: The length of the flat side is .Formula Used:The stress can be obtained as:

Q: 4. The figure shows a riveted lap joint with cover plates connecting two steel plates. Each rivet…

Q: IS used to höld a sign board with an axial load 50 kN as shown in figure. The end of the rod is 50…

Q: A. for the lap joint shown below, calculate the safe axial tensile force P if Otensile=136MP ,…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A steel sleeve coupling (see the figure below) is designed to join 2
externally threaded members. Make proper assumptions and calculate the minimum
thread diameter if the joint is loaded by axial static force F=30 kN. Materials used
have ơy
355 MPa. The safety factor should be 2.
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Solution

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Follow-up Questions

Read through expert solutions to related follow-up questions below.

Follow-up Question

how find the force?

Solution

by Bartleby Expert

SEE SOLUTION

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pls give right answer with step by step explanation. Design a clamp coupling for a shaft diameter of 60 mm. The torsional moment to be transmitted by this coupling taking in to account over loading as 160 N-m. The number of bolts used are 6 and the allowable stress in the material of the bolt is limited to 5N / m * m ^ 2 . The coefficient of friction between the shaft and muff material is 0.25.
The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load imposed on it. The bolts are -in coarse-thread SAE grade 8, tightened to recommended preload for nonpermanent assembly. The stiffnesses have already been computed and are kp=4 Mlb/in and km = 16 Mlb/in. Laad line F. Steady stress (a) Assuming that the bolts, rather than the welds, govern the strength of this design, determine the safe repeated load that can be imposed on this assembly using the Goodman criterion with the load line in the Figure and a fatigue design factor of 2. (b) Compute the static load factors based on the load found in part (a). (ie. Yielding factor of safety, Load factor of safety and factor against joint separation)
A bolted lap joint using ISO 5.8 bolts and members made from cold-drawn SAE 1040 steel is shown in the figure. Assume the bolt threads do not extend into the joint. Find the tensile shear load F that can be applied to this connection to provide a minimum factor of safety of 2.5 for the following failure modes: shear of bolts, bearing on bolts, bearing on members, and tension of members. 40 ↑ 70 40 ↑ 80 M20 × 2.5 20 20
The figure shows a section of a large coupling. Each bolt in this joint is subjected to cyclic load fluctuating between 0 and 13 kN. The members are made from steel. The members have equal thicknesses and total length of members is L=37 mm. Each bolt is initially tightened carefully to 78% of proof load. The bolt is to be Metric grade 5.8 M12x1.75 (coarse-pitch series). The threads has been manufactured by rolling and reliability for bolts is 95%. Calculate the stiffness of the bolt (in kN/mm). Yanıt:
Problem 17 A joint shown has the basic layout shown in the diagram below. (All dimensions on the diagram are in inches.) A single pin of diameter 0.5 inches (A = 0.2 in2) holds together the yoke and bar as shown. The material has an ultimate strength in tension of 80 ksi, and an ultimate strength in shear of 45 ksi. The load P has a value of 10000 lb. By examining the shear stress in the pin, the normal stress in the yoke, and the normal stress in the bar, find the overall factor of safety for the joint. P=10,000 lb YOKE -0.5 PIN BAR P=10,000 lb 1.5- 20 1.5 0.5 0.5
The figure illustrates the connection of a steel cylinder head to a grade 30 cast-iron pressure vessel using N bolts. A confined gasket seal has an effective sealing diameter D. The cylinder stores gas at a maximum pressure pg. For the specifications given in the table for the specific problem assigned, select a suitable bolt length from the preferred sizes in Table A–17, then determine the yielding factor of safety np, the load factor nL, and the joint separation factor n0. See problem number 8-36, and please use the FEA exponential curve-fit for member stiffness.
The eye screw, shown in the figure below is subjected to a force of 35 kN. The material of the screw is steel with ??=355 ???. The safety factor is 1,5. Calculate the minimum diameter of the thread.
Figure Q1 shows a structure under a concentrated force of P. Pins A, B, E, and F are single-shear with a 21-mm diameter. The connections at D is double shear connection with a 21-mm diameter. All pins are made of Aluminum 2014-T6. Based on yield stress, minimum factor of safety is 1.5 for all parts of below structure. Determine maximum concentrated force P, that can apply on the structure. (The cross sectional area of members EA and FB are 330 mm² and 250 mm² respectively). 350 mm 600 mm 900 mm E Copper Brass C83400 F Copper Bronze C86100 Figure Q1 A B 720 mm P D