A steel block has a length of 80 mm, width of 60 mm and thickness of 40 mm. The block is subjected to a uniform hydrostatic pressure of 180 kPa on all its faces. Modulus of elasticity E=200 GPa, Poisson’s ratio ?= 0.29. a.) Determine the bulk modulus of steel, b.) Determine the dilatation (e) of the material if e is the negative of the ratio of load to bulk modulus., and c.) Determine the change in volume of the steel block.

A steel block has a length of 80 mm, width of 60 mm and thickness of 40 mm. The block is subjected to a uniform hydrostatic pressure of 180 kPa on all its faces. Modulus of elasticity E=200 GPa, Poisson’s ratio ?= 0.29. a.) Determine the bulk modulus of steel, b.) Determine the dilatation (e) of the material if e is the negative of the ratio of load to bulk modulus., and c.) Determine the change in volume of the steel block.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.20P

See similar textbooks

Similar questions

Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
Determine the value of load P if At = 30 °C and the stress in bronze is limited to 132 MPa. Aluminum Bronze A = 600 mm? A = 500 mm? L= 2.0 m L= 2.50 m E = 70 GPa a = 23x10/ °C E = 83 GPa a = 18.90x10/ °C |c B D A O 2.0 m 3.0 m 1.0 m
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0 and if the elastic mođulus and length of the bar is 200 GPa and 2 m respectively, calculate the elongation in mm of the bar corresponding to the maximum load it can support. (А) 5 (в) 2.5 1.25 D) 0.625
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 760 mm. The cross-sectional dimensions of the beam are b1 = 34 mm, d1 = 106 mm, b2 = 20 mm, d2 = 20 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam.
A square plate O-P-Q-R of a linear elastic material with sides 1.0 m is loaded in a state of plane stress. Under a given stress condition, the plate deforms to a new configuration O-P'-Q'-R' as shown in figure (not to scale). Under the given deformation the edges of the plate remain straight. 10 mm y4 R'. Q' 10 mm R Q 10 mm P 20 mm The horizontal displacement of the point (0.5 m, 0.5 mm) in the plate O-P-Q-R (in mm, round off to one decimal place) is
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 780 mm. The cross-sectional dimensions of the beam are b₁ = 36 mm, d₁ = 104 mm, b₂ = 22 mm, d₂ = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 10 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 ✓ a M d₁ B L N.m A Answer: M = d₂ b₁
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 840 mm. The cross-sectional dimensions of the beam are b1 = 30 mm, d1 = 108 mm, b2 = 18 mm, d2 = 18 mm, and a = 6 mm. For this material, the allowable tensile bending stress is 17 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M. d2 d1 | A В
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm. The cross-sectional dimensions of the beam are b, = 36 mm, d1 = 95 mm, b2 = 22 mm, d2 = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 M d2 d1 |A В b1 Answer: M = N-m
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 900 mm. The cross-sectional dimensions of the beam are b1 = 31 mm, d1 = 119 mm, b2 = 19 mm, d2 = 19 mm, and a = 6 mm. For this material, the allowable tensile bending stress is 17 MPa, and the allowable compressive bending stress is 10 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M d2 |A В b1 Answer: M = i N-m
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E=69 GPa If Poisson's Ratio is 0.33, what will be the lateral strain? E=68 v=-e(lateral) e(axial)
Strain, Deformation and Thermal Stress Steel Rod A = 600 mm? L= 4.0 m E= 200 GPa Aluminum Rod A = 900 mm? a = 11.70 um/(m°C) L= 3.0 m E = 70 GPa %3D 2. Determine the stress in a = 23 um/(m°C) the aluminum rod if the 3 m 3 m 3 m temperature of steel is increased by 40 degrees A D Celsius at the same time the 50 KN load is applied to the beam. F = 50 KN Strain, Deformation and Thermal Stress · 600 KN The 600 KN load is horizontal when it is first 1.00 m applied to the columns. After some time, the 600 KN load is still horizontal after deformation took place for all the columns. If the diameter of all the columns is 50 mm. Modulus of elasticity of steel is 200 GPa and modulus of elasticity of bronze is 100 GPa. Compute the strain of the steel. 0.25 m Bronze Steel Bronze