A steel beam, of lengths a=4 m and b= 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 5.3 kN/m for AB span; and is constant with q= 5.3 kN/m for BC span. The Young's modulus of steel is 200 GPa. y A commitm Дв C b a 5 mm 200 mm 300 mm X

A steel beam, of lengths a=4 m and b= 3 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 5.3 kN/m for AB span; and is constant with q= 5.3 kN/m for BC span. The Young's modulus of steel is 200 GPa. y A commitm Дв C b a 5 mm 200 mm 300 mm X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A wooden beam whose length is 1 m is 100 mm wide and 200 mm high. It carries a load of 100 kN as shown. Determine the total tensile stress at A. Select the correct response: 32.48 MPa 29.98 MPa 52.46 MPa 34.98 MPa 50 500 mm- 30° 150 KN
A 4m long rectangular sectioned rigid solid pole with 30mm thickness is fixed to a wall in one end and supported 1 m away from the other end as shown in the figure. Calculate the maximum tensile & compressive stresses which occur in the pole material. 30 mm 1m 1 m 1 m 1 m 2 kN/m N 0007 120mm
Problem Set 1: A 6-m simply supported box beam is loaded as shown in the figure. Determine the maximum flexural stress in the beam. 30 kN 250mm 190mm 50 kN/m B 4m V V 2m 240mm 300mm
A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 465 mm². Determine the average axial stress in each bar. 85 kN 56 kN 2 m D 1m 1 m E 1m 1m F LL
An aluminum alloy pipe with an outside diameter of 5.7 in. and a wall thickness of 5/16 in. cantilevers upward a distance of L = 12 ft. The pipe is subjected to a wind loading that increases from wA = 7 lb/ft at its base to wB = 11 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
Problem.
A cantilever beam, 80 mm wide by 240 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1500 N/m at the wall. Determine the magnitude of the stress in a fiber 70 mm from the top of the beam at a section 6 m from the free end. Answer must be in MPa.
solve please ..
A cantilever beam, 90 mm wide by 280 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1300 N/m at the wall. Determine the magnitude of the stress in a fiber 60 mm from the top of the beam at a section 5 m from the free end. Answer must be in MPa.
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1531 N, T = 4945 Nm, a = 0.87 m, b = 1.05 m, c = 0.77 m, w = 32 mm, and h = 77 mm .
44
A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum pipes that have an outside diameter of 80mm and a wall thickness of 6mm. Determine the normal stress in each truss member. 1.0 m 1.5 m B 3.3 m 15 KN 12 kN 90 kip