A steam power plant uses the ideal Regenerative Rankine cycle with single open feedwater heater where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa then some steam is extracted at this point. The remaining steam expands and enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work.

A steam power plant uses the ideal Regenerative Rankine cycle with single open feedwater heater where the steam enters the high-pressure turbine at 4 MPa and 300C. It partially expands to 600 kPa then some steam is extracted at this point. The remaining steam expands and enters the condenser at 10 kPa. Sketch the schematic diagram and the TS diagram with labeled points, and solve for mass taken for feedwater heating, Qa, Qr, Wt, Wp, Wnet, thermal efficiency, and Steam rate. Neglect the condensate pump work.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3 (a) A simple Rankine cycle uses water as the working fluid (Figure Q3). IA 9 in 4s 4 gout Figure Q3. Rankine Cycle The boiler operates at 7,000 kPa and the condenser at 100 kPa. At the entrance to the turbine, the temperature is 450 °C. The isentropic efficiency of the turbine is 90%, pressure and pump losses are negligible, and the water leaving the condenser is subcooled by 9.6 °C. The boiler is sized for a mass flow rate of 20 kg/s. Determine, (i) The rate at which heat is added in the boiler, (ii) The power required to operate the pumps, (iii) The net power produced by the cycle, (iv) The thermal efficiency. (b) After a long walk in the 14 °C outdoors, a person wearing glasses enters a room at 25°C and 60% relative humidity. (i) What is the difference between specific and relative humidity? (ii) Please explain whether the glasses will become fogged or not and why. An
The engine on a steam ship runs on the Rankine cycle. The steam leaves the boiler at 20 bar and 350°C. The turbine has an efficiency of 75% and an outlet pressure of 1 bar. The pressure changes in the boiler and condenser can be considered negligible, and the liquid leaving the condenser is saturated. A. Determine the operating temperature of the condenser, and compute the efficiency of a Carnot cycle operating between the boiler and condenser temperatures. B. Determine the actual efficiency of this Rankine cycle and compare it to the Carnot efficiency. C. When the Titanic was sinking, the Carpathia received the S.O.S. and immediately set course to attempt a rescue. The captain of the Carpathia ordered the hot water turned off in the passengers’ cabins (Lord, 1955). What effect do you expect this action had?
turbine turbine Reheater (4 Boiler P4= P5 = Prcheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0 1 At state 1, the specific volume is 0.00101 m/kg Find the pressure in bar at state 6 to 3 decimal places
A power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It keeps the condenser at 45oC by transfer of 10 MW out as heat transfer. The first turbine section (high-pressure) expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Provide a detailed solution. Avoid shortcuts. Compute for the Pump work input (kJ/kg)
Q2. A cogeneration steam power plant has been modified with introducing an open feedwater heater as shown in figure below. Working pressure of the plant is between 6 MPa and 10 kPa for the boiler pressure and condensate pressure. The steam is extracted at 0.5 MPa for process heater and feedwater heater. The superheated srteam enters the turbine at 500°C at a rate of 25 kg/s and expands to the condensate pressure of 0.5 MPa. There is 60 percent of the steam is extracted from the turbine at the pressure of 0.5 MPa, and the remainder expands to a pressure of 10 kPa. Part of the extracted steam is used to heat feedwater and the rest of the extracted steam is used for process heating. The steam leaves the process heater as a saturated liquid at 0.5 MPa. It is subsequently mixed with the feedwater leaving the feedwater heater, and the mixture is pumped to the boiler pressure. The steam in the condenser is cooled and condensed by the cooling water from a nearby river, which enters the…
An r-134a refrigerator operates a simple vapor compression cycle (SVCC). The evaporatoroperates at -10 °C, while the condenser operates at 1 MPa. R-134a flows around the system at 10 g/s.a. Graph the cycle in a P-h diagram and calculate the temperature at the exit of the compressor, assuming it is 100% isentropicallyefficient.b. Calculate the power required by the compressor (in W) and the cooling effect of the refrigerator (in kW) c. Compute for the COP of the system. What is its percent difference from the reversible efficiency?
The net power (NOT TURBINE POWER) of the following steam power cycle is desired to be 25MW.Steam enters the turbine at 16 MPa, 450C, condenser at 10kPa pressure saturated liquid-steamIt enters as a mixture. Compressed liquid enters the pump at 9kPa at 35C and at 17MPacomes out. The inlet pressure to the boiler is 16.8MPa and 33C. The output from the boiler is 16.2MPa and 575C.The isentropic efficiency of the turbine is 90%, and that of the pump is 83%. Find the mass flow rate that will provide the required net power.
From the given data, if refrigerant circulation rate is 0.025kg/s, find the refrigerant effect of the ideal vapour compression cycle.
Please show the solution. Thank you very mmuch
Note : similar problem is already solved on bartleby.You can take help from there. Assume ideal and the inlet of pump is saturated liquid.