A steady, incompressible, two-dimensional velocity field is given by V = (u, v) = (0.65 + 1.7x)i + (1.3 – 1.7y)j where the x- and y- coordinates are in meters and the magnitude of velocity is in m/s. The x and y component of material acceleration a_x and a_y at the point (x=0 m, y= 0 m), respectively in m/s^2, are

A steady, incompressible, two-dimensional velocity field is given by V = (u, v) = (0.65 + 1.7x)i + (1.3 – 1.7y)j where the x- and y- coordinates are in meters and the magnitude of velocity is in m/s. The x and y component of material acceleration a_x and a_y at the point (x=0 m, y= 0 m), respectively in m/s^2, are

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DIPO Determine the slope at point B of the beam in the figure below. Assume the material's modulus of elasticity is 180 GPa, the beam's moment of inertia 360x10 mm4. 00 20 kN D 3 m 3 m 6 m A - I E=180 II !!
3- A steady, incompressible, two-dimensional velocity field is given by the following components in the xy-plane: u = 0.205 +0.97x+0.851y; v = v₁ +0.5953x -0.97y Calculate the acceleration field (find expressions for acceleration components ax and ay) and calculate the acceleration at the point (x, y) - (2, 1.5). Vo First names starting -1.650 with A to L
rd Determine the slope at point C of the beam in the figure below. Assume the material's modulus of elasticity is 200 GPa, the beam's moment of inertia = 360x106 mm4. 20 kN D 3 m 3 m 6 m II !!
Fluid Mechanics: Laminar flow occurs between two horzontal parallel plates under a pressure gradient dp/ds (p decreases in the positive s direction). The upper plate moves left (negative) at velocity ut. The expression of local velocity u is given in the attached equation. Is the magnitude of the shear stress greater at the moving plate (y=H), or the stationary plate (y=0)? Derive an expression for the y position of zero shear stress. Derive and expression for the plate speed ut required to make the shear stress zero at y=0.
Q3: Three forces are acting on a steel plate with 4m length by 4m width shown in figure. These three forces are required to cause a horizontal resultant acting through point A. If F = 405N, 1) The value of horizontal resultant R is: F E A B
The position of a particle moving along the x-axis is given by (X(t)=3t+2t^3 ). Find the acceleration a= 3+6t^2 ( m/sec2) 12 (m/sec2) 12 t ( m/ssec2) Object's mass is 15 kg is resting on a table. An external force ( 10 N) act with angle ( 30) on this object. Find the minimum force let it moving. ( g=10m/sec2) * 5 N 150 N 8.66 N
3Q. As a fluid flows through the fixed curved conduit in the figure shown, the velocity of particles is described by V = (0.4 s²) e 0.04 m/s, where s is in meters and t is in seconds. Determine the magnitude of the acceleration of the fluid particle located at point A, where s = 0.6 m, and the time of arrival is t = 1 s. The radius of curvature of the streamline at A is R = 0.5 m. s = 0.6 m 4
Consider the following steady, two-dimensional velocity field: √(u, v) = (0.21 +2.1x) + (-2.9-2.1y) i Calculate the location of the stagnation point. The location of the stagnation points are x = and y=
FA A vertical, circular cross-sectional jet of air strikes a conical deflector as indicated in Figure 3. A vertical anchoring force of FA = 0,20 N is required to hold the deflector in place. Considering the velocity of the air is measured as V=30 m/s and the diameter is + 60°- D=0,30 m, determine the mass (kg) of the deflector. The magnitude of velocity of the air remains constant. (SI Unit System) D V Figure 3
A light fixture of negligible mass, has three applied forces acting on it as shown. |F,| = 4 kN %3D 1.2 m 1.2 m 1.2 m 2.8 m |F,| = 6 kN y 45° |F = 5 kN Using the coordinate system shown, determine the components of vector F = Fxi + F,J +F,k (Answer in Kilo Newtons) Fy F2 F,
The 2.4kg particle moves in the horizontal x-y plane and has the velocity shown at time t=0. If theforce F = 2+3t^2/4 N, where t is time in seconds, is applied in the particle in the y-direction beginning attime t = 0, determine the velocity of the particle 4s after F is applied and specify the corresponding anglemeasured counter clockwise from the x-axis to the direction of the velocity
A steady, incompressible, two-dimensional velocity field is given by the following components in the xy-plane: u = 0.205 + 0.97x + 0.851y ; v = Vo + 0.5953x - 0.97y %D