A square pile group of 9 piles passes through a recently filled up material of 3.5 m depth. The diameter of the pile is 30 cm and placed at spacing of 0.8 m centre to centre. The unconfined compressive strength of the material is 60 kN/m² and the unit weight of recently filled up material is 16 kN/m³. The negative skin friction (in kN, rounded off to one decimal place) would be.

A square pile group of 9 piles passes through a recently filled up material of 3.5 m depth. The diameter of the pile is 30 cm and placed at spacing of 0.8 m centre to centre. The unconfined compressive strength of the material is 60 kN/m² and the unit weight of recently filled up material is 16 kN/m³. The negative skin friction (in kN, rounded off to one decimal place) would be.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The wooden pile shown in the figure has a diameter of 100 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 4.99 kN/m. The length of the pile is L = 4.2 m and its elastic modulus is E = 8.7 GPa.Calculate(a) the force FB needed at the base of the pile for equilibrium.(b) the magnitude of the downward displacement at A relative to B.
Q- A pile of 0.50 m diameter and of length 10 m is embedded in a deposit of clay. The undrained strength parameters of the clay are cohesion = 60 kN/m² and the angle of internal friction = 0. Find the skin friction capacity (kN) of the pile for an adhesion factor of 0.6.
PILE FOUNDATIONS • Example: 35/1 A machine foundation is supported by four prestressed concrete plies driven to bedrock. The length of each pile is 24 m, and they are 0.3 mx 0.3 m in cross section. The weight of the machine and the foundation is 1360 kN. Given: unit weight of concrete = 24 kN/m¹ and the modulus of elasticity of the concrete used for the piles = 24.5 × 106 kPa. Determine the natural frequency of the pile foundation system.
3. A concrete pile 15.24 m long having a cross section of 406 mm × 406 mm is fully embedded in a saturated clay layer for which Ysat 19.02 kN/m³, Ø = 0, and cu=76.7 kN/m². Determine the allowable load that the pile can carry (Assuming FS-3). Use the a method to estimate the skin friction and Vesic's method for point load estimation.
The wooden pile shown in the figure has a diameter of 105 mm and is subjected to a load of P = 70 kN. Along the length of the pile and around its perimeter, soil supplies a constant frictional resistance of w = 3.85 kN/m. The length of the pile is L = 4.0 m and its elastic modulus is E= 12.9 GPa. Calculate (a) the force Fg needed at the base of the pile for equilibrium. (b) the magnitude of the downward displacement at A relative to B. y L Answers: (a) FB = (b) UA= i i B FB KN mm
Q1: Determine the allowable load capacity for the driven pile of 0.6 m diameter embedded in a layered soil as shown in the figure below, use F.S 2.0 , K, = 1.5 and tand =0.5? ELEV. 110 N.C.C W.T ELEV. 108 Cu =70 kPa Y = 17 kN/m3 a = 1, yw = 10 kN/m? ELEV. 102 O.C.C, Cu 180 kPa, y = 20 kN/m³ a = 0.45 ELEV. 98 Sandy Layer Yt = 19 kN/m3 Ø = 32° Nq = 23.18 ELEV. 90
A reinforced concrete circular pile is driven to the soil as shown below. Calculate the negative skin friction force acting on the pile.
A square concrete pile of 10 m length is driven into a deep layer of uniform homogeneous clay. The average unconfined compressive strength of the clay, determined through laboratory tests on undisturbed samples extracted from the clay layer, is 100 kPa. If the ultimate compressive load capacity of the driven pile is 632 kN, the required width of the pile is mm. (in integer) (Bearing capacity factor Nc = 9; adhesion factor a = 0.7)
A pile of diameter 250 mm is installed in a soil strata with a recently filled layer of clay of 3 m depth. The unit cohesion of the material is 18 kN/m² and unit weight of soil is 15 kN/m². The negative skin friction on the pile is equal to. (assume adhesion factor = 0.4)