A square footing is to be used to support a 300mm by 300mm RC column loaded with 500 kN dead load and 230 kN live load. If the net allowable bearing capacity is 330 kPa, determine the size of the footing. Determine also the minimum thickness based on one way shear and two way shear. Use f'c = 21 MPa and fy = 345 MPa. Use d = t - cc - 1.5db. %3D %D

A square footing is to be used to support a 300mm by 300mm RC column loaded with 500 kN dead load and 230 kN live load. If the net allowable bearing capacity is 330 kPa, determine the size of the footing. Determine also the minimum thickness based on one way shear and two way shear. Use f'c = 21 MPa and fy = 345 MPa. Use d = t - cc - 1.5db. %3D %D

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Shallow Foundations: Ultimate Bearing Capacity

Section: Chapter Questions

Problem 6.2P: A 5.0 ft wide square footing is placed at 3.0 ft depth within the ground where c = 200 lb/ft2, =...

See similar textbooks

Similar questions

A continuous foundation is required in a soil where c=10kN/m2, =26, and =19.0kN/m3. The depth of the footing will be 1.0 m. The dead load and the live load are 600 kN/m and 400 kN/m, respectively. Determine the required width for the foundation based on allowable stress design with FS = 3, using Eq. (6.10) and Table 6.1.
Design a square pad footing with an overall depth of 600mm, cover to the reinforcements 50mm with 20mm diameter reinforcement bars in both directions. The footing carries a 400mm square column with a dead load of 1050KN and imposed load of 300KN. The safe bearing capacity of the soil is 170KN/m^2, fcu 30N/mm^2. Assume a unit weight of concrete to be 24KN/m^3 and footing weight 150KN
Given the following:Column: 600 mm x 600 mmAxial Dead Load = 1680 kNAxial Live Load = 1350 kNDepth of footing = 1.8 mAllowable soil pressure = 230 kPaUnit weight of soil above footing = 16 kN/m 3Unit weight of concrete = 24 kN/m 3fc' = 28 MPafy = 345 MPaDesign the footing if its width is limited to 3.2 m. Use 25 mm bars and 75 mm clear concrete cover. Useload factor of 1.4 DL + 1.7 LL.
A column 500 mm x 500 mm square is supported by a 3.5 m x 3.5 m isolated spread footing. The column carries a dead load of 1200 kN and a live load of 1000 kN. The total depth of the footing is 550 mm with steel cover of 100 mm. Use NSCP 2001 provisions. Determine the punching shear stress at ultimate loads. A 1830.00 kPa 2154.11 kPa 1566.48 kPa D 1331.52 kPa
A square footing is to be designed to carry a total axial load of 5000kg. The bottom of the footing is 2.8m below the ground surface, and the groundwater table is located at the bottom of the footing. Take PDRY = 1860kg/m3 and PSAT = 1950kg/m3, c = 1600kg/m2, Ø = 30degrees. Use the given Chart for the 90 80 70 determination of the bearing capacity factors. a. Determine the dimension of the footing using a factor of safety of 2. b. Compute the ultimate bearing capacity of the soil in kPa. Compute the net allowable bearing capacity of the soil. 60 Ng Nr 50 С. 40 30 20 10 10 20 30 40 50 Friction Angle Nc, Nq, Nr
B Jf g is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth (D) of the footing from punching shear consideration is
A square footing 2.5m x 2.5 m supports a square column 300mm x 300mm at its center. Concrete cover to bar centroid = 100mm. Ultimate load combination is 1.2DL + 1.6L. Column loads aee service conditions:DL = 680 kN LL = 400kNf'c = 20.7 Mpa fy = 275 MPa Calculate the nominal punching-shear stress acting at the critical section of the footing slab if the thickness of the slab is 450 mm. (Correct Answer 1.99)
B Calculate the ratio of the Ultimate Shear Force to Shear Capacity in one-way shear. Consider critical case only. A rectangular footing has dimensions shown and is acted upon by a dead load of 653 kN and a live load of 647 kN. The column dimension is 269x677 mm where the shorter dimension is parallel to B. The thickness of the footing is 442mm. f'c-28 MPa and fy=420 MPa for diameter 20mm bars. A=2.9m and B=4.8m
A square footing 2.5m x 2.5 m supports a square column 300mm x 300mm at its center. Concrete cover to bar centroid = 100mm. Ultimate load combination is 1.2DL + 1.6L. Column loads aee service conditions: DL= 680 KN LL = 400KN f'c = 20.7 Mpa fy = 275 MPa Calculate the nominal punching-shear stress acting at the critical section of the footing slab if the thickness of the slab is 450 mm.
A strap footing consists of two footings connected by strap beam. Allowable soil pressure is 450 kPa. Footing thickness is 600mm and the bottom of the footing is 1.5m below the ground. Assume soil weight to be 19 Kn/m3 and concrete weight to be 24 Kn/m³. Use f'c = 20.7 Mpa and fy = 414 Mpa. Use 1.2DL + 1.6LL. gog = galow - footing weight – soil weight. DL = 275 kN LL = 400 kN DL = 600 kN LL = 500 kN 4.8 m 400 x 400 column 400 x 400 column 1.2 m 1.2 m a) Calculate the footing dimensions. (Size is in multiples of 100 mm) b) Draw the Shear and Moment Diagram on the Longitudinal Direction. Show the maximum shear and moment.
A 6ft x 6ft foundation is subjected to an axial load Q = 225k and a moment M = 100k ft. The depth of footing is 5ft. The soil unit wt is 125pcf, phi = 32deg and c=1000psf Find: 9min qmax e L' qult using the general BC equation
A footing supporting a 2 ft x 2 ft column load carring 550 kips (dead load) and 200 kips (live load). The foundation level is 5 ft below the ground surface. The gross allowable bearing capacity is 6 ksf. The unit of soil is 130 pcf. You are required to provide complete design calculations for bearing, shear, and flexure for the strip footing. Assume f' = 4 ksi, fy = 60 ksi.