A spur gear set is shown in Figure Q6(a). The pinion 2 rotates at 750 revolutions/minute and transmits 1.8 kW to the driven gear 3. The teeth pressure angle is 20 degrees with a module m = 2.5 mm. 30 Teeth - 20 Teeth Figure Q6(a) Determine the forces that act on gear 3 from the pinion. i). ii). Draw a free-body diagram of gear 3.

A spur gear set is shown in Figure Q6(a). The pinion 2 rotates at 750 revolutions/minute and transmits 1.8 kW to the driven gear 3. The teeth pressure angle is 20 degrees with a module m = 2.5 mm. 30 Teeth - 20 Teeth Figure Q6(a) Determine the forces that act on gear 3 from the pinion. i). ii). Draw a free-body diagram of gear 3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure below shows a two-stage helical gear set. Pinion 2, which is in the converter position, transfers a certain rotation moment from the shaft to gear 3 in the first stage by rotating in the direction of the clock in the front view (or in the Z direction) shown in the figure. on shaft B, the pinion gear No. 4 is positioned with gear No. 3, which receives and/or transmits the drive from different gears. The number 4 Pinion in the second stage drives the number 5 gear, converting the input moment in the system to the output moment and providing movement transfer. Answer the figure in the table as follows by determining the direction of rotation of Gears 3, 4 and 5 and the Helix direction of each gear when looking at the left side view of the figure from the left (i.e. from the-z direction).Also, briefly explain how the concept of a module in Gears is determined by showing the basic dimensions on a tooth form and what the main law of gears refers to by drawing a figure.
Parvinbhai
Figure Q2-1 shows a schematic of the power train for 2012 Nissan Leaf pure electric cars, which includes a two stage gearbox (a compound train). The numbers of teeth of the gears in the gearbox are N1=N3=17, N2=31 and N4=74. The motor speed at an engine power of P = 80 kW is nmotor (n1) = 9,795 rpm. N2=31 T 2012 LEAF Driveline from Motor to Axle: 17T 31T N1=N3 =17 T 17T 74 T - Wheels I N4=74 T Motor Figure Q2-1 What are the necessary and sufficient requirements for the two stage gearbox to mesh properly for power transmission? i) Calculate the rotating speed (nwheel or n4) and the torque Twheel or T4 on the axle of the driven wheels. Neglect power loss of the gearbox. ii) nmotor(n1)=9,795 rpm in kilometre per hour? You may assume the diameter of the wheels to be D = Ø600 mm. What is the speed of the Nissan Leaf car when the motor speed is at AXLE AXLE
A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is triple threaded and has 65 mm pitch diameter. The tooth form is to be 20 degrees full depth involute. Determine: a) the lead and lead angle of the worm A. b) The center distance between worm and gear. c) The tangential force acting on worm. d) The axial force acting on worm e) The radial force acting on worm
A planetary gear train is shown in the figure. The sun gear (gear 1) is fixed, it has a 1-in. pitch diameter with a diametral pitch of 12. Gear 3 has 36 teeth and gear 4 has 20 teeth. Gear 5 has 40 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6), which serves as the output from the train and has 160 teeth. The carrier (link 2) serves as the input to the train, determine the rotational velocity of the ring gear when the input shaft rotates at 1125 rpm clockwise.
pls expalin to me step by step and write clearly. i will rate your answer immediately thanks
(3) A mechanism consists of two flexible shafts: shaft1 and shaft 2 which are connected by gear I and gear 2. Each shaft is fixed on one end at a fixed support. Gear 1 J.N Fored Support Shaft 1 Fied Support Shaft 2 Gear 2 length of shaft 1: 1 = 0.3 m; length of shaft 2: 1= 0.2 m; diameter of shaft 1 and shaft 2: d=0.01m; gear number N-48; gear number Ny= 24; density of shaft I and shaft 2 material p = 6000 kg/m³. the two gears have moment of inertia J 4 10 kg m², and J;= 1-10* kg m² Determine the equivalent moment of inertia, Jeg, of the system at the coordinate Oj shown in the figure.
The spur gear arrangement shown in the figure has a pinion (diver Gear A) that rotates at 625 rpm, an idler Gear B and a driven gear (Gear C). The gears have a module of 5 mm and a pressure angle of 20 degrees. Given the number of teeth as shown in the figure, determine: i) ii) iii) The pitch diameters of each of the gears. The torque that each shaft is required to transmit. The forces on each of the gears 40 teeth 490⁰ B 70 teeth 50 teeth
5.A pair of gears has these parameters: teeth of two gears are Z1=26, Z2=52, modulus m=1.25mm. Please calculate (1)the radius of reference circle of two gears, r1 and r2 (2) The pitch of this pair of gears, p (3) The standard center distance, a (4) Now two gears are mounted with a'=49mm, calculate the radius of two pitch circle for two gears, r1' and r2' . (5)The ratio of angular velocity of two gears, i.